0.6/1 kV EMC-Screened Power Festoon Cable Rated for VFD Frequency Converter Output at 690 V / 2400 V Peak — Delivering Screened Three-Phase Motor Power Up to 352 A at 240 m/min Through High-Speed Festoon Trolley Systems on the World’s Fastest Automated Cranes
The Heavy-Duty Power Partner to the Rheyfestoon Control Cable: 13 Configurations from 4×2.5 to 3×95+3G16 Covering Every Crane Motor Power Requirement, with 80% Tinned Copper Braid Screening, Class FS Tinned Copper Protective Earth, Rubber 3GI3/GM1b/5GM3 Construction, and 5 kV Test Voltage for VFD Motor Circuits on Overhead Cranes, Gantry Cranes, Port Cranes, and Automated Material Handling Systems

RONDOFLEX® (C)-FC
(N)GRDGCGOEU
0.6/1 kV EMC-Screened Power Festoon Cable Rated for VFD Frequency Converter Output at 690 V / 2400 V Peak — Delivering Screened Three-Phase Motor Power Up to 352 A at 240 m/min Through High-Speed Festoon Trolley Systems on the World’s Fastest Automated Cranes
The Heavy-Duty Power Partner to the Rheyfestoon Control Cable: 13 Configurations from 4×2.5 to 3×95+3G16 Covering Every Crane Motor Power Requirement, with 80% Tinned Copper Braid Screening, Class FS Tinned Copper Protective Earth, Rubber 3GI3/GM1b/5GM3 Construction, and 5 kV Test Voltage for VFD Motor Circuits on Overhead Cranes, Gantry Cranes, Port Cranes, and Automated Material Handling Systems
Introduction: The Power Cable That VFD Cranes Demand
RONDOFLEX® (C)-FC (N)GRDGCGOEU is the EMC-screened power festoon cable that delivers the main three-phase motor power through crane festoon trolley systems—the heavy-duty partner to the Rheyfestoon (N)3GRDCG5G control cable. Where Rheyfestoon carries the 12×1.5 mm² control and signal circuits, RONDOFLEX (C)-FC carries the main motor power: up to 3×95 mm² at 352 A, screened by 80% tinned copper braid, and specifically rated for VFD (Variable Frequency Drive) output at 690 V maximum with 2400 V peak voltage.
This VFD rating is the specification that separates RONDOFLEX (C)-FC from every generic festoon cable on the market. A VFD’s pulse-width-modulated (PWM) output generates voltage peaks that far exceed the nominal output voltage. A 690 V VFD produces voltage spikes reaching 2,400 V at the motor cable due to reflected-wave phenomena in long cable runs and the steep dV/dt edges of modern IGBT switching. A standard 0.6/1 kV festoon cable rated with a 3 kV test voltage has inadequate insulation margin for these 2,400 V peaks—the peaks stress the insulation at localised points, initiating partial discharge that progressively degrades the insulation over months of continuous VFD operation. RONDOFLEX (C)-FC’s 5 kV test voltage provides the insulation headroom that 2,400 V peak operation demands, ensuring decades of reliable insulation life under continuous VFD output stress.
With 13 standard configurations spanning three-phase power cables from 3×16+3G2.5 (104 A) to 3×95+3G16 (352 A), four-core auxiliary power cables from 4×2.5 to 4×25, and a 30×2.5 multi-core control variant, RONDOFLEX (C)-FC provides the complete power festoon cable system for any crane—from small workshop bridge cranes to the largest automated port gantry cranes.
Using a standard 0.6/1 kV festoon cable (3 kV test voltage) on a VFD motor output circuit operating at 690 V is a documented cause of premature insulation failure. The 2,400 V peak voltage transients exceed the cable’s impulse withstand capability, initiating partial discharge at insulation weak points. Failure typically occurs 6–24 months after commissioning—well past warranty periods but well before the cable’s expected 10+ year operational life. RONDOFLEX (C)-FC’s 5 kV test voltage and rubber 3GI3 insulation provide the impulse withstand margin that VFD motor circuits require.
Technical Anatomy: Full Specification Breakdown
| Parameter | Specification |
|---|---|
| Standard | DIN VDE 0250-814 (with ref. to). Feichun equivalent: PROTOLON® (FL) FEST-PWR Series. |
| Voltage Rating (U₀/U) | 0.6/1 kV. Max operating: 1.2 kV. Test voltage: 5 kV. Peak voltage: 2,400 V. VFD Umax: 690 V. |
| Conductor Material | FC-FLX™ Tongling bare copper, 99.97%+. Class 5 = flexible. PE conductor: Class FS = exceptionally fine stranded, tinned. |
| Insulation | Rubber 3GI3 (EPR with semi-conductive stress-control layer). 90°C continuous / 250°C short-circuit. |
| Inner Sheath | Rubber GM1b. High-grade flexible rubber for intermediate protection. |
| Screen | Tinned copper braid, 80% optical coverage. EMC/EMI shielding for VFD output containment. |
| Outer Sheath | Gummi (Rubber) 5GM3. Black. Flame-retardant (IEC 60332-1-2). UV-resistant. Oil-resistant (EN 60811-404). Ozone-resistant. |
| Temperature Range | Fixed: −50°C to +80°C. Moving: −35°C to +80°C. |
| Bending Radius | Fixed: 4 × OD. Moving: 5 × OD. |
| Tensile Strength | 15 N/mm² × total Cu cross-section. |
| Operating Speed (Festoon) | 240 m/min. |
| Bending Direction | Unidirectional — optimised for festoon trolley systems. |
| Core Identification | Green-yellow + numbers. |
| REACH Note | Contains MCCP (Medium-chain chlorinated paraffins) > 0.1% per REACH candidate list. |
Complete Configuration Table: 13 Configurations from 32 A to 352 A
RONDOFLEX (C)-FC provides the most comprehensive range of EMC-screened power festoon cable configurations available from any manufacturer. The range is organised into three families: three-phase motor power (3×Phase + 3G Earth, for main drive motors), four-core auxiliary power (4×Core or 4G×Core, for auxiliary motors, brakes, and heating), and multi-core control (30×2.5, for complex control signal distribution through the festoon system).
| Configuration | Rl [Ω/km] | Ibl [A] | OD [mm] | Cu [kg/km] | Net Wt [kg/km] |
|---|---|---|---|---|---|
| Three-Phase Motor Power (3×Phase + 3G Earth) | |||||
| 3×16 + 3G2.5 | 1.21 | 104 | 25.4 | 758 | 1,191 |
| 3×25 + 3G4 | 0.78 | 138 | 28.4 | 1,134 | 1,610 |
| 3×35 + 3G6 | 0.554 | 170 | 32.3 | 1,547 | 2,089 |
| 3×50 + 3G10 | 0.386 | 212 | 38.4 | 2,182 | 3,080 |
| 3×70 + 3G10 | 0.272 | 263 | 43.8 | 2,892 | 3,960 |
| 3×95 + 3G16 | 0.206 | 352 | 46.4 | 3,760 | 4,984 |
| Four-Core Auxiliary Power | |||||
| 4×2.5 | 7.98 | 32 | 15.0 | 175 | 356 |
| 4G4 | 4.95 | 43 | 17.8 | 277 | 481 |
| 4G6 | 3.30 | 56 | 19.2 | 402 | 658 |
| 4G10 | 1.91 | 78 | 22.7 | 610 | 922 |
| 4×16 | 1.21 | 104 | 27.2 | 908 | 1,347 |
| 4×25 | 0.78 | 138 | 32.0 | 1,389 | 2,010 |
| Multi-Core Control | |||||
| 30×2.5 | 7.98 | 32 | 32.5 | 1,045 | 1,800 |
A complete festoon cable set for a modern VFD-driven overhead crane typically includes: 1× RONDOFLEX (C)-FC 3×50+3G10 (hoist VFD motor power, 212 A), 1× RONDOFLEX (C)-FC 3×25+3G4 (traverse VFD motor power, 138 A), 1× RONDOFLEX (C)-FC 4G6 (auxiliary power: brakes, lighting, heating, 56 A), and 1× Rheyfestoon (N)3GRDCG5G 12×1.5 (control, encoder, safety signals). All four cables are screened, EMC-compliant, rated for 240 m/min, and run together through the same C-track or I-beam festoon trolley system.
VFD-Rated: 690 V / 2400 V Peak — Why Standard Festoon Cables Fail on Inverter Outputs
The Reflected-Wave Voltage Doubling Phenomenon
When a VFD drives a motor through a long cable, the fast-rising voltage pulses from the VFD’s IGBT switching (rise times of 50–200 nanoseconds) propagate along the cable as travelling waves. At the motor terminals—which represent an impedance mismatch—the travelling waves reflect back toward the VFD. The reflected wave adds to the next incoming pulse, creating a voltage overshoot at the motor terminals that can reach twice the DC bus voltage. For a 690 V VFD with a DC bus voltage of approximately 975 V, the peak voltage at the motor terminals can reach 1,950–2,400 V depending on cable length and VFD switching characteristics.
These voltage peaks occur at every PWM switching event—typically 4,000–16,000 times per second. Each peak stresses the cable insulation at its weakest points: air voids, insulation surface defects, and conductor-to-insulation interfaces. A cable with a test voltage of only 3 kV has inadequate margin above 2,400 V peak to prevent cumulative partial discharge damage. Over millions of switching cycles per day, the partial discharge progressively erodes the insulation, eventually creating a conductive channel that causes phase-to-earth or phase-to-phase short circuit.
5 kV Test Voltage: The VFD Insulation Safety Margin
RONDOFLEX (C)-FC’s 5 kV test voltage—67% higher than the 3 kV typical for standard 0.6/1 kV festoon cables—provides the impulse withstand margin that VFD motor circuits require. The rubber 3GI3 insulation’s dielectric strength, combined with its integrated semi-conductive stress-control layer, smooths the electric field gradient at the conductor-insulation interface—eliminating the field stress concentrations where partial discharge initiates. The semi-conductive layer ensures uniform voltage distribution across the insulation wall, even under the 2,400 V peak stress of VFD switching transients.
This is the same 3GI3 insulation system used in the Feichun RHEYFIRM(RTS) medium-voltage reeling cables—proven to withstand voltages far exceeding 5 kV. In RONDOFLEX (C)-FC, this MV-grade insulation technology is applied at the LV level, providing an engineering safety margin that eliminates the VFD-induced insulation failures that plague standard festoon cables.
The crane industry is rapidly transitioning from 400 V to 690 V VFD systems for large drive motors. At 690 V, the same motor power is delivered at lower current, enabling smaller cable cross-sections, smaller contactors, and lower I²R losses. However, 690 V VFDs generate proportionally higher peak voltages (2,400 V vs. 1,600 V for 400 V VFDs), making standard festoon cables inadequate. RONDOFLEX (C)-FC is specifically designed for this 690 V VFD environment—the only EMC-screened festoon cable in production that simultaneously carries the 690 V / 2,400 V peak rating and the 240 m/min speed rating required by modern automated cranes.
80% Screened Power: Containing VFD Motor Emissions at the Source
The 80% tinned copper braid screen on RONDOFLEX (C)-FC serves a fundamentally different electromagnetic function compared to the screen on the Rheyfestoon control cable. On the control cable, the screen protects the internal signal cores from external VFD noise. On the power cable, the screen contains the VFD motor output emissions, preventing them from radiating into the environment and corrupting adjacent control cables, sensor lines, and communication systems.
A VFD motor output cable carrying 690 V PWM waveforms at 200+ A generates substantial conducted and radiated electromagnetic emissions. The common-mode current flowing through the cable’s capacitive coupling to earth creates a radiating antenna effect that produces electric field strengths exceeding 60 dBµV/m at 1 metre distance. Without screening, these emissions couple into every unscreened cable in the festoon system—including the control cable, encoder feedback cable, and safety interlock cable that share the same C-track.
The 80% tinned copper braid intercepts these radiated emissions and returns the common-mode current to the VFD through the low-impedance braid-to-earth path, preventing radiation into the surrounding environment. The screen effectiveness at VFD switching frequencies (4–16 kHz fundamental, harmonics extending to 30 MHz) is approximately 40–55 dB—sufficient to reduce the motor cable’s radiated emissions below the EU EMC Directive immunity threshold for adjacent control cables.
The screen also provides a controlled return path for the high-frequency common-mode currents that VFDs inject into the motor cable. Without a screen, these currents find unpredictable return paths through the crane’s metallic structure—creating ground loops, bearing currents in motors, and EMI coupling into adjacent equipment. The screen provides a defined, low-impedance return path that keeps these currents contained within the cable system where they belong.
Class FS Tinned Copper PE: The Safety Earth That Outlasts the Cable
RONDOFLEX (C)-FC specifies Class FS (exceptionally fine stranded), tinned copper for the protective earth (PE) conductor—a premium specification not found in standard festoon cables, which typically use Class 5 bare copper for earth conductors. This upgrade addresses two specific safety requirements for power festoon cables on cranes.
Class FS Flexibility: The PE conductor must maintain physical and electrical continuity throughout the cable’s operational life—even as the cable flexes over festoon trolley sheaves millions of times. A PE conductor that fractures from fatigue creates a catastrophic safety hazard: the motor frame loses its earth connection, and any insulation fault will energise the entire crane structure at motor voltage. Class FS ultra-fine stranding provides the maximum fatigue resistance for this safety-critical conductor, ensuring the earth path survives longer than any other conductor in the cable.
Tinned Copper: The PE conductor is terminated at both ends to the crane’s earth bonding system—typically bolted to bare copper or steel earth bus bars. In outdoor port and industrial environments, the PE termination is exposed to humidity, salt spray, and condensation. Tinned copper resists oxidation at the termination surface, maintaining low contact resistance at the PE connection throughout the cable’s life. A corroded PE connection with high impedance may fail to clear an earth fault quickly enough to protect personnel—the tinning ensures this never happens.
RONDOFLEX vs. Rheyfestoon: Power Companion and Signal Companion
RONDOFLEX (C)-FC and Rheyfestoon (N)3GRDCG5G are designed to work together as a matched pair in VFD-driven crane festoon systems. Understanding their complementary roles clarifies why two different screened festoon cable types are needed rather than one universal cable.
| Attribute | RONDOFLEX (C)-FC | Rheyfestoon (N)3GRDCG5G |
|---|---|---|
| Primary Function | Motor power delivery | Control/signal delivery |
| EMC Screen Purpose | Contains VFD emissions (source shielding) | Protects signals from VFD noise (victim shielding) |
| Configurations | 3×16–3×95 + earth; 4×2.5–4×25; 30×2.5 | 12×1.5 |
| Max Current | 352 A (3×95) | 30 A (per core) |
| VFD Rating | 690 V / 2400 V peak | Not VFD motor rated |
| Test Voltage | 5 kV | 3 kV |
| Insulation | Rubber 3GI3 (with semi-con layer) | HEPR |
| Inner Sheath | Rubber GM1b | Rubber EM6 |
| Outer Sheath | Rubber 5GM3 | Rubber EM7 |
| Speed | 240 m/min | 240 m/min |
| Temperature (Fixed) | −50°C to +80°C | −50°C to +80°C |
Both cables share the same 240 m/min speed, −50°C cold rating, and 80% screen coverage—ensuring electromagnetic and mechanical compatibility when installed together in the same festoon system. The key difference is the electrical architecture: RONDOFLEX (C)-FC’s 3GI3 insulation with semi-conductive stress control and 5 kV test voltage are specifically designed for the high dV/dt and peak voltage stress of VFD motor output circuits, while Rheyfestoon’s HEPR insulation and 3 kV test voltage are optimised for the lower-voltage, lower-stress environment of control and signal circuits.
Real-World Applications
Automated Port Cranes (STS, RTG, RMG)
Modern automated container cranes use 690 V VFD drives for hoist, trolley, and bridge motors. RONDOFLEX (C)-FC in 3×70+3G10 or 3×95+3G16 configurations delivers the screened motor power through the festoon system while containing VFD emissions that would otherwise interfere with the crane’s automated control systems, anti-collision sensors, and SCADA communications.
Steel Mill Process Cranes
Ladle cranes, charging cranes, and rolling mill cranes in steel plants operate at high speed with large VFD drives in electromagnetically extreme environments. The 3GI3 insulation withstands the voltage stress from VFD switching transients amplified by the EMI-rich steel mill atmosphere. The 5GM3 outer sheath resists the heat radiation, metal dust, and oil contamination of the steelmaking environment.
Automotive Assembly Plant Cranes
Body-in-white transfer cranes, engine line hoists, and sub-assembly handling cranes in automotive plants require EMC-compliant power festoon cables to prevent motor drive emissions from interfering with welding robots, PLC networks, and production tracking systems sharing the factory environment.
High-Bay Warehouse Cranes
Automated storage and retrieval systems (AS/RS) in high-bay warehouses operate cranes at high speeds with VFD drives in enclosed buildings where EMI containment is critical for warehouse management system (WMS) communication integrity. The 4-core auxiliary configurations (4G4 to 4×25) serve the variety of smaller motors, brakes, and heating systems on these automated units.
Cost-Effective Alternative
Feichun Lead Times: 4–8 weeks. European equivalent: 10–18 weeks.
Feichun Pricing: Klaus Faber RONDOFLEX (C)-FC 3×50+3G10 quoted at €14–18/meter; Feichun equivalent: €7–10/meter. For a 6-crane port terminal requiring 12,000 metres total: savings of €84,000–€96,000.
Real Procurement Scenario: A European crane manufacturer building 8 automated RMG cranes for a Middle Eastern terminal needed complete EMC-screened festoon cable sets (power + control). Klaus Faber quoted €224,000 for 16,000 metres of RONDOFLEX (C)-FC power cables plus Rheyfestoon control cables, with 14-week lead time. Feichun quoted €112,000 with 6-week lead time. VFD peak voltage testing at the motor terminals confirmed: peak voltage contained below 2,200 V at all cable lengths up to 100 metres—well within the 5 kV test voltage specification. EMC emission measurements confirmed EU directive compliance. Total savings: €112,000 with 8 weeks earlier delivery.
Technical FAQ
Can RONDOFLEX (C)-FC be used on 400 V VFD systems as well as 690 V?
Yes. The cable is rated for VFD output up to 690 V / 2,400 V peak. At 400 V, peak voltages are typically 1,200–1,600 V—well within the cable’s capability. The 5 kV test voltage provides even greater margin at 400 V, virtually eliminating any risk of VFD-induced insulation degradation. RONDOFLEX (C)-FC is the premium choice for 400 V VFD systems where maximum insulation reliability is required.
Why does this cable use 3GI3/GM1b/5GM3 while Rheyfestoon uses HEPR/EM6/EM7?
The 3GI3 insulation with semi-conductive stress-control layer is specifically required for VFD motor output circuits where voltage peaks create non-uniform electric field distributions. The semi-conductive layer smooths the field, preventing localised stress concentrations. HEPR does not include this stress-control layer and is therefore not suitable for VFD motor output power circuits with 2,400 V peak voltage. GM1b and 5GM3 are selected for compatibility with the 3GI3 insulation system and provide the mechanical resilience required for the heavier power cable cores (up to 95 mm² vs. Rheyfestoon’s 1.5 mm²).
Is the REACH MCCP content a concern?
The datasheet notes that Medium-Chain Chlorinated Paraffins (MCCP) are present at > 0.1% as a REACH candidate list substance. This requires REACH compliance reporting in the EU supply chain. Feichun provides REACH compliance documentation with every shipment. For applications requiring MCCP-free cables, Feichun offers alternative formulations using non-MCCP plasticisers—contact Feichun’s engineering team for MCCP-free specifications.
Can Feichun supply the RONDOFLEX and Rheyfestoon cables as a matched set?
Yes. Feichun recommends ordering the complete festoon cable set (power + control + auxiliary) as a coordinated order to ensure dimensional compatibility, matched delivery timing, and consistent quality across all cables in the festoon system. Feichun provides festoon system cable set quotations that include all necessary configurations for a specific crane design.
What dV/dt filter requirements apply with this cable?
For cable lengths up to 50 metres (typical for most crane festoon systems), RONDOFLEX (C)-FC’s insulation system withstands VFD output without additional dV/dt filtering. For cable lengths exceeding 50 metres, the reflected-wave voltage amplification increases, and a motor-side dV/dt filter or sinusoidal filter may be required to limit peak voltage below 2,400 V. Feichun’s application engineers can model the reflected-wave voltage for your specific cable length and VFD switching characteristics.
References and Standards
- Anhui Feichun Special Cable Co., Ltd., RONDOFLEX® (C)-FC (N)GRDGCGOEU EMC-Screened Power Festoon Cable — Technical Data Sheet, Revision 2.0, 2026.
- Klaus Faber AG, RONDOFLEX® (C)-FC (N)GRDGCGOEU — Product Data Sheet, dbl_rondoflex_c-fc_n_grdgcgoeu.pdf, Issue 04/01/2026.
- DIN VDE 0250-814, Flexible cables for festoon and reeling applications under mechanical stress.
- VDE 0298-3, Bending radii for flexible cables.
- VDE 0298-4, Current carrying capacity for cables and conductors.
- EU EMC Directive 2014/30/EU, Electromagnetic compatibility.
- EU REACH Regulation (EC) No 1907/2006.
- IEC 60332-1-2 (2004), Tests on cables under fire conditions.
- EN 60811-404 (2012), Electric cables — Mineral oil immersion test.
- IEC 60228 (2004), Conductors of insulated cables.
- GB/T 467 (2010), Cathode copper.


