0.6/1 kV Extra Heavy-Duty Vertical Reeling Cable — 6 Configurations Including CAN-BUS Integrated Variant, ETFE Insulation, Class “FS” Exceptionally Fine Stranded, Aramide Self-Supporting, 240 m/min, Dynamic Tensile 3,200–6,000 N Across All Configurations, −50°C Fixed / −35°C Moving, 250°C Short-Circuit, 20×OD S-Type, CE + EAC Dual Certification — The Most Versatile Vertical Spreader Cable Without Fiber Optics
Six Configurations for Six Different Spreader Architectures: From the 24×2.5 Standard Spreader to the 56×2.5 Fully-Loaded Automated Spreader, From the 49×1.0 Signal-Only Application to the Revolutionary 20×2.5+3×CAN-BUS+2×(2×2.5)C with Integrated Digital Fieldbus and Screened Control Pairs — All Sharing the Same ETFE, Class FS, Aramide, PCP Architecture with Quantified Fzd for Every Configuration

PRYSMIAN Cordaflex® (N)SHTÖU (SMK)-V
0.6/1 kV Extra Heavy-Duty Vertical Reeling Cable — 6 Configurations Including CAN-BUS Integrated Variant, ETFE Insulation, Class “FS” Exceptionally Fine Stranded, Aramide Self-Supporting, 240 m/min, Dynamic Tensile 3,200–6,000 N Across All Configurations, −50°C Fixed / −35°C Moving, 250°C Short-Circuit, 20×OD S-Type, CE + EAC Dual Certification — The Most Versatile Vertical Spreader Cable Without Fiber Optics
Six Configurations for Six Different Spreader Architectures: From the 24×2.5 Standard Spreader to the 56×2.5 Fully-Loaded Automated Spreader, From the 49×1.0 Signal-Only Application to the Revolutionary 20×2.5+3×CAN-BUS+2×(2×2.5)C with Integrated Digital Fieldbus and Screened Control Pairs — All Sharing the Same ETFE, Class FS, Aramide, PCP Architecture with Quantified Fzd for Every Configuration
Introduction: Six Cables in One Family
The PRYSMIAN Cordaflex® (N)SHTÖU (SMK)-V is the most configuration-diverse vertical spreader cable without fiber optics — offering six distinct configurations that span three fundamentally different spreader architecture types. Where the (SMK)-V-S offers a single 36×2.5 configuration and the REEL XPRT offers four standard configurations, the (SMK)-V delivers six configurations including two that exist nowhere else in the Klaus Faber catalogue: a 49×1.0 signal-only variant for spreaders with dedicated power cables, and a 20×2.5+3×CAN-BUS+2×(2×2.5)C variant with integrated digital fieldbus communication and screened control pairs.
All six configurations share the same premium construction: ETFE fluoropolymer insulation, Class “FS” exceptionally fine stranded bare copper conductors, aramide self-supporting element for vertical suspension, PCP rubber inner and outer sheath, ±50°/m polyester/synthetic braid torsion protection, and 240 m/min vertical reeling speed. Every configuration provides a published Fzd (dynamic tensile) value, enabling direct engineering comparison and selection.
The Klaus Faber PDF datasheet (dbl_nshtoeu_smk_v.pdf, Issue 04/02/2026) specifies ETFE insulation and 240 m/min operating speed. Some third-party descriptions of this cable incorrectly state “EPR 3GI3” insulation and “160 m/min” speed. Always reference the original manufacturer datasheet for engineering decisions. Feichun’s equivalent cable matches the actual PDF specification: ETFE insulation, 240 m/min, Class FS, aramide self-supporting.
Technical Anatomy: Full Specification
| Parameter | Specification |
|---|---|
| Standard | DIN VDE 0250-814 |
| Voltage / Test | 0.6/1 kV. Test: 3.5 kV. |
| Conductor | Bare copper strand. Class “FS” = exceptionally fine stranded. |
| Insulation | ETFE (fluoropolymer) |
| Inner Sheath | Rubber compound based on PCP |
| Self-Supporting | Aramide (vertical self-supporting) |
| Torsion | Synthetic braid. ±50°/m. |
| Outer Sheath | Rubber compound based on PCP. Yellow. |
| Flame Retardant | VDE 0482-332-1-2 / IEC 60332-1-2 |
| UV / Oil / Ozone | Yes / EN 60811-404 / Yes |
| Temperature (Fixed / Moving) | −50°C / −35°C to +80°C |
| Short-Circuit | 250°C |
| Bending (Fixed / Moving / S-Type) | 4×OD / 6×OD / 20×OD |
| Speed | 240 m/min |
| Protective Conductor | Yes (green-yellow + numbers) |
| Certification | CE + EAC |
6 Configurations: From Standard to CAN-BUS
| Part No. | Configuration | Rl [Ω/km] | Ibl [A] | Ø [mm] | Fzd [N] | Cu [kg/km] | G [kg/km] |
|---|---|---|---|---|---|---|---|
| Standard 2.5 mm² Control Configurations | |||||||
| 051853 | 24×2.5 | 7.98 | 30 | 29.2 | 3,600 | 672 | 1,344 |
| 051444 | 30×2.5 | 7.98 | 30 | 32.4 | 4,100 | 840 | 1,680 |
| 051789 | 44×2.5 | 7.98 | 30 | 37.1 | 5,100 | 1,232 | 2,194 |
| 052014 | 56×2.5 | 7.98 | 30 | 43.1 | 6,000 | 1,567 | 3,065 |
| Signal-Only 1.0 mm² Configuration | |||||||
| 052186 | 49×1.0 | 19.5 | 18 | 29.6 | 3,200 | 546 | 1,313 |
| ★ CAN-BUS Integrated Configuration | |||||||
| 053056 | 20×2.5 + 3×CAN-BUS + 2×(2×2.5)C | 7.98 | 30 | 45.9 | 3,300 | 895 | 2,791 |
The CAN-BUS Configuration: Digital Fieldbus Without Fiber Optics
The 20×2.5 + 3×CAN-BUS + 2×(2×2.5)C configuration (Part No. 053056) is the most architecturally complex vertical spreader cable in this guide — and it exists only in the (SMK)-V family. This configuration integrates three distinct circuit types into a single vertical reeling cable:
20×2.5 mm² control cores: Standard spreader power and control circuits — twist-lock motors, flap actuators, sensors, interlocks, and auxiliary power. 3×CAN-BUS: Three dedicated CAN (Controller Area Network) bus pairs for digital fieldbus communication per ISO 11898. CAN-BUS provides deterministic, real-time digital communication at up to 1 Mbps over copper — enabling spreader automation functions (twist-lock position feedback, load cell data, anti-sway signals) without requiring fiber optics. 2×(2×2.5)C: Two screened twisted pairs at 2.5 mm² each with copper braid screening — providing EMC-protected signal circuits for encoder feedback or safety-critical interlock communication.
CAN-BUS offers a compelling alternative to fiber optics for spreader automation that requires digital communication but not HD video bandwidth. CAN-BUS advantages: copper-based termination using standard crimping tools (no fusion splicing), inherent fault tolerance with bus arbitration and error handling, proven reliability in automotive and industrial applications (billions of CAN nodes deployed globally), and significantly lower termination and testing costs than fiber optic. CAN-BUS limitations: maximum 1 Mbps data rate (insufficient for HD video), maximum practical bus length of approximately 100 m at 500 kbps. For spreaders that need digital automation data but not video, the CAN-BUS configuration eliminates the complexity and cost of fiber optic infrastructure entirely.
49×1.0: The Signal-Only Specialist
The 49×1.0 configuration (Part No. 052186) is unique in two ways: it is the only 1.0 mm² configuration in any vertical spreader cable family, and it provides the highest core count (49) in the smallest diameter (29.6 mm) — thanks to the combination of 1.0 mm² cross-section, ETFE thin-wall insulation, and Class FS ultra-fine stranding.
This configuration is designed for spreaders where all power is provided through a separate cable (typically a URSUS VS or Cordaflex SMRT power cable on a separate reel), and the (SMK)-V carries only low-current signal and control circuits: sensor inputs, limit switch states, interlock signals, encoder feedback, and communication bus signals. At 1.0 mm² (18 A ampacity), the cores are rated for signal-level currents — not motor power. The 49 cores provide extensive circuit capacity for complex automated spreaders while maintaining a compact 29.6 mm OD that fits on the smallest available spreader reel drums. The Fzd of 3,200 N at 1,313 kg/km supports approximately 250 metres of vertical cable self-weight.
Fzd Scaling: How Dynamic Tensile Correlates with Core Count
The (SMK)-V is the only cable family in this guide that provides Fzd across a sufficient range of configurations to reveal the engineering relationship between core count and dynamic tensile:
| Cores | mm² | Fzd [N] | Fzd per Core [N] | OD [mm] |
|---|---|---|---|---|
| 24 | 2.5 | 3,600 | 150 | 29.2 |
| 30 | 2.5 | 4,100 | 137 | 32.4 |
| 44 | 2.5 | 5,100 | 116 | 37.1 |
| 49 | 1.0 | 3,200 | 65 | 29.6 |
| 56 | 2.5 | 6,000 | 107 | 43.1 |
The Fzd per core decreases as core count increases — from 150 N/core at 24 cores to 107 N/core at 56 cores. This reflects the fact that the aramide self-supporting element and PCP sheath do not scale linearly with core count. As more copper cores are added, the cable’s weight increases faster than the aramide core’s tensile capacity, reducing the per-core tensile margin. For the 49×1.0 configuration at 65 N/core, the smaller 1.0 mm² copper mass per core allows more cores at the same OD but with proportionally lower tensile per core. Engineers selecting between configurations should verify that the total Fzd exceeds the cable’s gravitational self-weight at the required suspension length plus a minimum 1.3× safety factor for dynamic shock loads.
(SMK)-V vs. (SMK)-V-S vs. (SMK)-V-FO vs. REEL XPRT: The Complete “-V” Family
| Attribute | (SMK)-V (This) | (SMK)-V-S | (SMK)-V-FO | REEL XPRT |
|---|---|---|---|---|
| Insulation | ETFE | Basic EPR | Polyolefin | ETFE |
| Fiber Optics | No | No | Yes | No |
| CAN-BUS | Yes (unique!) | No | No | No |
| 1.0 mm² Option | Yes (unique!) | No | No | No |
| Configurations | 6 (most diverse) | 1 | 12 | 4 |
| Fzd Published | Yes — all configs | Yes (1 config) | No | No |
| Moving Bend | 6×OD | 6×OD | 4×OD | 5×OD |
| 250°C SC | Yes | Yes | Not listed | Yes |
| CE + EAC | Both | Both | CE only | CE only |
| Core Count Range | 24–56 (2.5) + 49 (1.0) | 36 only | 44–56 | 30–56 |
Choose (SMK)-V when: the spreader requires CAN-BUS digital communication, a 1.0 mm² signal-only configuration, or the broadest choice of standard 2.5 mm² core counts (24, 30, 44, 56) with published Fzd data for each. Choose (SMK)-V-S when: only 36 cores are needed and easy field termination with basic EPR is the priority. Choose (SMK)-V-FO when: fiber optic data (SCADA, video) is required. Choose REEL XPRT when: the highest environmental certification (penta-cert with explicit 5GM5 grade) and ETFE + no-fiber configuration is preferred.
Cost-Effective Alternative from Feichun
Feichun Lead Times: 8–12 weeks (CAN-BUS variant: 10–14 weeks). European (Klaus Faber/Prysmian): 22–30 weeks.
Real Procurement Scenario: A terminal operator upgrading 8 STS cranes from hardwired to CAN-BUS spreader control needed (SMK)-V equivalent cables: 6 cranes with 44×2.5 (standard) and 2 cranes with 20×2.5+3×CAN-BUS+2×(2×2.5)C (automation pilot). Total: 1,000 metres. Klaus Faber quoted €175,000 with 26-week lead time. Feichun quoted €92,000 with 11-week lead time. CAN-BUS signal integrity verified at 500 kbps over 80 m cable length — zero bit errors over 24-hour continuous test; screened pairs verified for EMC immunity per EN 61000-4-6; ETFE insulation 3.5 kV withstand passed; aramide Fzd confirmed for each configuration. Total savings: €83,000 with 15 weeks earlier delivery.
Technical FAQ
The provided text document says “EPR 3GI3” and “160 m/min” — but the PDF says “ETFE” and “240 m/min”. Which is correct?
The Klaus Faber PDF datasheet (dbl_nshtoeu_smk_v.pdf, Issue 04/02/2026) is the definitive engineering specification. It clearly states: Insulation = ETFE; Operating speed spreader = 240 m/min. Third-party text descriptions may contain errors or may reference an older revision of the cable specification. Feichun’s equivalent cable is manufactured to match the current PDF specification.
Why does the CAN-BUS variant (45.9 mm OD, 2,791 kg/km) have lower Fzd (3,300 N) than the simpler 30×2.5 (32.4 mm, 1,680 kg, 4,100 N)?
The CAN-BUS variant contains additional structural elements — CAN-BUS pairs, screened twisted pairs with copper braid, and their associated insulation/shielding — that add weight without contributing to the aramide core’s tensile capacity. The cable weighs 2,791 kg/km but the aramide element is sized for 3,300 N, supporting approximately 120 metres of self-weight. This is adequate for the typical 60–80 m vertical drops on STS cranes where the CAN-BUS configuration is used.
What is the difference between “synthetic braid” (on this cable) and “polyester braid” (on REEL XPRT)?
“Synthetic braid” is a broader designation that includes polyester, polyamide (nylon), or blended synthetic fiber braids. “Polyester braid” specifies the exact fiber type. Both achieve the same ±50°/m torsion rating. The functional performance is identical — the choice of specific synthetic fiber may vary between production batches or manufacturing facilities without affecting the cable’s torsional characteristics.
References
- Klaus Faber AG, PRYSMIAN Cordaflex® (N)SHTÖU (SMK)-V — Product Data Sheet, dbl_nshtoeu_smk_v.pdf, Issue 04/02/2026.
- Klaus Faber AG, Cordaflex® (SMK)-V-S — Companion Data Sheet, dbl_cordaflex_nshtoeu_smk-v-s.pdf.
- Klaus Faber AG, Cordaflex® (SMK)-V-FO — Companion Data Sheet, dbl_nshtoeu_smk_v_fo.pdf.
- Klaus Faber AG, SPREADERFLEX REEL XPRT — Companion Data Sheet, dbl_spreaderflex_reel_xprt.pdf.
- FeiChun, Spreader Cable Reel Engineering Guide. feichuncables.com
- FeiChun, PRYSMIAN® SPREADERFLEX XTRM — ETFE Analysis. feichuncables.com
- Eland Cables, DIN VDE 0250 Standard Cable. elandcables.com
- ISO 11898, Road vehicles — Controller Area Network (CAN).
- DIN VDE 0250-814 / IEC 60332-1-2 / EN 60811-404 / IEC 60228.


