[email protected]

Flame retardance

15 Min Read
BASKET SPREADER 750: Next-Generation Hoisting Cable Architecture The BASKET SPREADER 750 (3GSLTOE) represents a fundamental advancement in hoisting control cable design, specifically engineered for next-generation automated port crane systems operating under extreme environmental and operational constraints. Unlike the BASKET SPREADER 740's 300/500V AC specification, the 750 operates at 0.6/1kV AC with dual-voltage DC capability (0.9/1.8 kV)—a classification shift that enables: Higher power capacity – 2–3× greater amperage per conductor, enabling longer cable runs with lower voltage drop Medium-voltage infrastructure compatibility – Direct integration with port substation power distribution systems (0.6 kV = 600V three-phase industrial standard) DC dual-voltage operation – Simultaneous support for AC motor control and DC feedback/signaling circuits (0.9/1.8 kV DC margins) Extreme temperature capability – Operating range −50°C to +80°C (vs. SPREADER 740's −20°C to +60°C), addressing Arctic port terminals and tropical high-ambient scenarios Advanced insulation chemistry – GAALTHERM® 530 thermoplastic compound replaces standard PVC/PUR, delivering superior chemical resistance and thermal stability This cable bridges the gap between standard control cables (300/500V, limited temperature) and heavy industrial medium-voltage distribution cables, creating a purpose-built solution for modern automated gantry crane systems in global port terminals.
Technical Department
on12/06/2026

Что такое ÖLFLEX® INSTRUM RE-Y(ST)YRY: инженерный анализ армированного heat resistant PVC кабеля с общим экраном

ÖLFLEX® INSTRUM RE-Y(ST)YRY — это армированный heat resistant PVC instrumentation/data cable с PVC (V-90HT) core insulation, overall screen, PVC inner sheath, galvanized steel wire armour and PVC outer sheath. Кабель предназначен для communication, data and voice transmission signal в industrial process manufacturing plants, Oil and Gas industry and petrochemical industry. По предоставленным данным он основан на EN 50288-7, имеет flame retardance according to IEC 60332-3-24, stranded plain annealed copper wires according to BS 6360 / IEC 60228 Class 2, aluminium polyester tape collective screen, tinned copper drain wire, black PVC inner sheath and black or blue PVC outer sheath.
13 Min Read
BASKET SPREADER 750: Next-Generation Hoisting Cable Architecture The BASKET SPREADER 750 (3GSLTOE) represents a fundamental advancement in hoisting control cable design, specifically engineered for next-generation automated port crane systems operating under extreme environmental and operational constraints. Unlike the BASKET SPREADER 740's 300/500V AC specification, the 750 operates at 0.6/1kV AC with dual-voltage DC capability (0.9/1.8 kV)—a classification shift that enables: Higher power capacity – 2–3× greater amperage per conductor, enabling longer cable runs with lower voltage drop Medium-voltage infrastructure compatibility – Direct integration with port substation power distribution systems (0.6 kV = 600V three-phase industrial standard) DC dual-voltage operation – Simultaneous support for AC motor control and DC feedback/signaling circuits (0.9/1.8 kV DC margins) Extreme temperature capability – Operating range −50°C to +80°C (vs. SPREADER 740's −20°C to +60°C), addressing Arctic port terminals and tropical high-ambient scenarios Advanced insulation chemistry – GAALTHERM® 530 thermoplastic compound replaces standard PVC/PUR, delivering superior chemical resistance and thermal stability This cable bridges the gap between standard control cables (300/500V, limited temperature) and heavy industrial medium-voltage distribution cables, creating a purpose-built solution for modern automated gantry crane systems in global port terminals.
Technical Department
on12/06/2026

Что такое ÖLFLEX® INSTRUM RE-2X(ST)Y: инженерный анализ неармированного инструментального кабеля с XLPE изоляцией и общим экраном

ÖLFLEX® INSTRUM RE-2X(ST)Y — это un-armoured instrumentation cable с XLPE core insulation и overall screen, предназначенный для communication, data and voice transmission signal в industrial process manufacturing plants, Oil and Gas industry and petrochemical industry. По предоставленным данным кабель основан на EN 50288-7, имеет flame retardance according to IEC 60332-3-24, stranded plain annealed copper wires, XLPE insulation, aluminium polyester tape collective screen, tinned copper drain wire and PVC outer sheath in black or blue.
14 Min Read
FC-PNCT-R and FC-PNCT(S)-R reinforced festoon cables represent the premium tier of overhead power distribution technology, engineered for next-generation crane systems demanding superior electrical performance, extended service life, electromagnetic compatibility, and multi-circuit power distribution capabilities. Reinforced festoon cables incorporate a fundamentally different architecture compared to standard festoon cables—adding mechanical reinforcement (braid-tape structure), overall electromagnetic shielding (in the shielded variant), and optimized multi-core configurations supporting independent circuit distribution. These enhancements address the operational requirements of modern automated port equipment, VFD-driven crane systems, and advanced cargo handling machinery. Key Design Innovations: • Integrated Reinforcement Layer: A tape-braid composite structure carrying a portion of mechanical stress, extending insulation life and reducing temperature rise during operation • Overall Screen Shielding: Tinned copper braid surrounding the entire cable assembly (in FC-PNCT(S)-R variant) providing complete electromagnetic protection • Multi-Core Architecture: 3–30 independent conductor cores enabling single-cable distribution for complex equipment with multiple independent motor systems • Size Flexibility: Three conductor size options (1.5, 2.5, 4.0) scaled to specific application requirements and current demands These innovations enable reinforced festoon cables to deliver 7–10 year service intervals in demanding applications—approximately 40–60% longer than standard festoon cables. For terminal operators prioritizing equipment reliability and minimizing replacement downtime, the premium investment in reinforced cables delivers outstanding value.
Technical Department
on14/04/2026

FC-PNCT-R/FC-PNCT(S)-R Reinforced Festoon Cables

FC-PNCT-R and FC-PNCT(S)-R reinforced festoon cables represent the premium tier of overhead power distribution technology, engineered for next-generation crane systems demanding superior electrical performance, extended service life, electromagnetic compatibility, and multi-circuit power distribution capabilities. Reinforced festoon cables incorporate a fundamentally different architecture compared to standard festoon cables—adding mechanical reinforcement (braid-tape structure), overall electromagnetic shielding (in the shielded variant), and optimized multi-core configurations supporting independent circuit distribution. These enhancements address the operational requirements of modern automated port equipment, VFD-driven crane systems, and advanced cargo handling machinery. Key Design Innovations: • Integrated Reinforcement Layer: A tape-braid composite structure carrying a portion of mechanical stress, extending insulation life and reducing temperature rise during operation • Overall Screen Shielding: Tinned copper braid surrounding the entire cable assembly (in FC-PNCT(S)-R variant) providing complete electromagnetic protection • Multi-Core Architecture: 3–30 independent conductor cores enabling single-cable distribution for complex equipment with multiple independent motor systems • Size Flexibility: Three conductor size options (1.5, 2.5, 4.0) scaled to specific application requirements and current demands These innovations enable reinforced festoon cables to deliver 7–10 year service intervals in demanding applications—approximately 40–60% longer than standard festoon cables. For terminal operators prioritizing equipment reliability and minimizing replacement downtime, the premium investment in reinforced cables delivers outstanding value.
14 Min Read
Festoon cables (also called curtain cables or loop cables) are specialized power distribution cables designed for overhead, suspended installations where the cable hangs in loops from fixed support points while a moving trolley or crane pulls the cable along beneath it. The term "festoon" derives from the architectural practice of hanging decorative swags between fixed points—a metaphor that accurately describes how these cables are installed in crane systems. FC-PNCT festoon cables serve as the primary power supply for overhead equipment including container cranes, gantry cranes, overhead bridge cranes, and related port equipment. The cable hangs in a series of gentle loops from fixed hanger points spaced approximately 5–10 meters apart. As the crane moves along the runway, the moving trolley pulls the cable along with it, creating a smooth, coordinated motion that maintains electrical contact between fixed shore power and the moving equipment. Festoon cables experience fundamentally different stresses compared to reel-mounted high-tension cables: • Repetitive bending cycles as the cable forms and reforms loops—but at a slower rate than reel cables • Lower tensile stress because the cable hangs relatively stationary between support points • Environmental exposure to saltwater spray, UV radiation, and thermal cycling—same as reel cables • Gentle, predictable bending geometry with consistent bend radii determined by hanger spacing • Lower operational temperature due to reduced mechanical stress and typically lower current demands These differences necessitate a distinctly different cable design optimized specifically for festoon applications. Festoon cables prioritize superior bending flexibility, excellent environmental resistance, and long-term durability under repetitive but gentle mechanical stress.
Technical Department
on14/04/2026

FC-PNCT Korean Standard Festoon Cables

Festoon cables (also called curtain cables or loop cables) are specialized power distribution cables designed for overhead, suspended installations where the cable hangs in loops from fixed support points while a moving trolley or crane pulls the cable along beneath it. The term “festoon” derives from the architectural practice of hanging decorative swags between fixed points—a metaphor that accurately describes how these cables are installed in crane systems. FC-PNCT festoon cables serve as the primary power supply for overhead equipment including container cranes, gantry cranes, overhead bridge cranes, and related port equipment. The cable hangs in a series of gentle loops from fixed hanger points spaced approximately 5–10 meters apart. As the crane moves along the runway, the moving trolley pulls the cable along with it, creating a smooth, coordinated motion that maintains electrical contact between fixed shore power and the moving equipment. Festoon cables experience fundamentally different stresses compared to reel-mounted high-tension cables: • Repetitive bending cycles as the cable forms and reforms loops—but at a slower rate than reel cables • Lower tensile stress because the cable hangs relatively stationary between support points • Environmental exposure to saltwater spray, UV radiation, and thermal cycling—same as reel cables • Gentle, predictable bending geometry with consistent bend radii determined by hanger spacing • Lower operational temperature due to reduced mechanical stress and typically lower current demands These differences necessitate a distinctly different cable design optimized specifically for festoon applications. Festoon cables prioritize superior bending flexibility, excellent environmental resistance, and long-term durability under repetitive but gentle mechanical stress.
15 Min Read
HT-PNCT cable family represents a comprehensive, professional ecosystem of high-tension power distribution cables engineered to serve the complete spectrum of port equipment applications. Rather than a single cable type, HT-PNCT encompasses a carefully developed family of variants, each optimized for specific application requirements, electrical loads, environmental conditions, and operational constraints. The family architecture is organized around five core cable types: 1. HT-PNCT-RF — Reinforced Festoon variant with large conductor sizes (240–300 sq mm) and flexible sheath options (1.5, 2.5, 4.0 mm). Optimized for extended-span festoon applications with demanding tensile and environmental requirements. 2. HT-PNCT (Standard) — Non-shielded multi-core configuration (3–30 conductor cores) with optimized conductor size and sheath thickness combinations. Base specification for equipment without sensitive electronics or electromagnetic sensitivity. 3. HT-PNCT(S) — Shielded variant of standard cable featuring tinned copper braid shield. Engineered for equipment with variable frequency drive (VFD) motors, crane controls, and sensitive automation electronics requiring electromagnetic interference (EMI) attenuation. 4. HT-PNCT-R — Reinforced non-shielded variant with enhanced mechanical strength and extended tensile capacity. For applications requiring maximum tensile strength without electromagnetic protection needs. 5. HT-PNCT(S)-R — Premium reinforced-shielded variant combining maximum tensile strength with full electromagnetic protection. For next-generation high-power equipment with VFD systems and extreme service life requirements. This family structure enables terminal operators to select the optimal cable for each specific application—balancing performance, cost, environmental requirements, and operational constraints. The shared engineering platform across family members ensures interoperability and simplifies spare cable management.
Technical Department
on13/04/2026

Complete HT-PNCT High Tension Cable Family

HT-PNCT cable family represents a comprehensive, professional ecosystem of high-tension power distribution cables engineered to serve the complete spectrum of port equipment applications. Rather than a single cable type, HT-PNCT encompasses a carefully developed family of variants, each optimized for specific application requirements, electrical loads, environmental conditions, and operational constraints. The family architecture is organized around five core cable types: 1. HT-PNCT-RF — Reinforced Festoon variant with large conductor sizes (240–300 sq mm) and flexible sheath options (1.5, 2.5, 4.0 mm). Optimized for extended-span festoon applications with demanding tensile and environmental requirements. 2. HT-PNCT (Standard) — Non-shielded multi-core configuration (3–30 conductor cores) with optimized conductor size and sheath thickness combinations. Base specification for equipment without sensitive electronics or electromagnetic sensitivity. 3. HT-PNCT(S) — Shielded variant of standard cable featuring tinned copper braid shield. Engineered for equipment with variable frequency drive (VFD) motors, crane controls, and sensitive automation electronics requiring electromagnetic interference (EMI) attenuation. 4. HT-PNCT-R — Reinforced non-shielded variant with enhanced mechanical strength and extended tensile capacity. For applications requiring maximum tensile strength without electromagnetic protection needs. 5. HT-PNCT(S)-R — Premium reinforced-shielded variant combining maximum tensile strength with full electromagnetic protection. For next-generation high-power equipment with VFD systems and extreme service life requirements. This family structure enables terminal operators to select the optimal cable for each specific application—balancing performance, cost, environmental requirements, and operational constraints. The shared engineering platform across family members ensures interoperability and simplifies spare cable management.
15 Min Read
HT-PNCT-F cable, Korean standard cable, high tension cable, port equipment cable, festoon-reel cable, unloader cable, stacker cable, reclaimer cable, gantry crane cable, tape braid reinforcement, 0.6/1KV cable, KSC 3317, IEC 60502-1, tape reinforcement, braid reinforcement, cable architecture, layer structure, synthetic tape, polyester tape, polypropylene tape, braid layer, glass-fiber reinforced nylon, hybrid reinforcement, tape-braid hybrid, load-carrying mechanism, copper conductor, Class 2 stranding, EP rubber insulation, chloroprene sheath, outer diameter, cable weight, conductor resistance, insulation resistance, test voltage, dielectric strength, tensile strength, flex-cycle endurance, impact resistance, bending flexibility, reelability, environmental durability, saltwater resistance, UV resistance, thermal cycling, flame retardance, operational temperature, 3-core configuration, 4-core configuration, conductor size range, ship unloader, gantry crane, stacker reclaimer, mobile harbour crane, conveyor drive system, reel preparation, minimum bend radius, cable winding, slip ring termination, preventive maintenance, insulation resistance test, quality assurance, electrical testing, mechanical testing, reinforcement layer testing, environmental testing, reel-specific testing, ASTM B117, IEC 60811, ISO 12947, IEC 60331-1, Feichun HT-PNCT-F, HT-PNCT-F-S shielded, HT-PNCT-F-EX enhanced braid, HT-PNCT-F-SX full premium, VFD cable, EMI shielding, port terminal, Busan port, Korean Industrial Standard, festoon power supply, reel-mounted equipment
Technical Department
on13/04/2026

HT-PNCT-F Korean Standard High Tension Cables

HT-PNCT-F cable, Korean standard cable, high tension cable, port equipment cable, festoon-reel cable, unloader cable, stacker cable, reclaimer cable, gantry crane cable, tape braid reinforcement, 0.6/1KV cable, KSC 3317, IEC 60502-1, tape reinforcement, braid reinforcement, cable architecture, layer structure, synthetic tape, polyester tape, polypropylene tape, braid layer, glass-fiber reinforced nylon, hybrid reinforcement, tape-braid hybrid, load-carrying mechanism, copper conductor, Class 2 stranding, EP rubber insulation, chloroprene sheath, outer diameter, cable weight, conductor resistance, insulation resistance, test voltage, dielectric strength, tensile strength, flex-cycle endurance, impact resistance, bending flexibility, reelability, environmental durability, saltwater resistance, UV resistance, thermal cycling, flame retardance, operational temperature, 3-core configuration, 4-core configuration, conductor size range, ship unloader, gantry crane, stacker reclaimer, mobile harbour crane, conveyor drive system, reel preparation, minimum bend radius, cable winding, slip ring termination, preventive maintenance, insulation resistance test, quality assurance, electrical testing, mechanical testing, reinforcement layer testing, environmental testing, reel-specific testing, ASTM B117, IEC 60811, ISO 12947, IEC 60331-1, Feichun HT-PNCT-F, HT-PNCT-F-S shielded, HT-PNCT-F-EX enhanced braid, HT-PNCT-F-SX full premium, VFD cable, EMI shielding, port terminal, Busan port, Korean Industrial Standard, festoon power supply, reel-mounted equipment
10 Min Read
High Tension (HT) cables are specialized power distribution cables designed for reel-mounted applications in port equipment—primarily unloaders, stackers, reclaimers, and gantry cranes. The term "high tension" does not refer to electrical voltage (HT cables are 0.6/1 kV, standard port equipment voltage); instead, it refers to the mechanical tension and stress that these cables experience when wound on reels and unwound during equipment operation. HT-PNCT cables serve as the primary power supply line running from the equipment's fixed power source (shore power or generator) to the reel-mounted slip ring assembly on moving equipment. During operation, these cables are repeatedly wound onto and unwound from rotating reels, experiencing: • Tensile stress from the cable's own weight as it hangs from the reel to the equipment • Bending stress each time the cable wraps around the reel drum • Mechanical abrasion from friction against the reel surface and cable guides • Environmental exposure to saltwater spray, UV radiation, and thermal cycling Standard festoon cables (like FC-PNCT) are optimized for relatively stationary installations. HT-PNCT cables are engineered specifically for reel-wound, dynamic applications where these mechanical stresses dominate the cable's service life.
Technical Department
on13/04/2026

HT-PNCT High Tension Cables

High Tension (HT) cables are specialized power distribution cables designed for reel-mounted applications in port equipment—primarily unloaders, stackers, reclaimers, and gantry cranes. The term “high tension” does not refer to electrical voltage (HT cables are 0.6/1 kV, standard port equipment voltage); instead, it refers to the mechanical tension and stress that these cables experience when wound on reels and unwound during equipment operation. HT-PNCT cables serve as the primary power supply line running from the equipment’s fixed power source (shore power or generator) to the reel-mounted slip ring assembly on moving equipment. During operation, these cables are repeatedly wound onto and unwound from rotating reels, experiencing: • Tensile stress from the cable’s own weight as it hangs from the reel to the equipment • Bending stress each time the cable wraps around the reel drum • Mechanical abrasion from friction against the reel surface and cable guides • Environmental exposure to saltwater spray, UV radiation, and thermal cycling Standard festoon cables (like FC-PNCT) are optimized for relatively stationary installations. HT-PNCT cables are engineered specifically for reel-wound, dynamic applications where these mechanical stresses dominate the cable’s service life.
22 Min Read
DIN VDE 0250-813 Cable
Technical Department
on10/11/2025

What is DIN VDE 0250-813 Cable?

DIN VDE 0250-813 represents the German national standard governing the design, construction, and performance requirements for trailing cables used in power installations serving mobile equipment and heavy industrial machinery. Published in May 1985 and maintained by the Deutsches Institut für Normung (German National Standard) in conjunction with VDE (Verband der Elektrotechnik), this comprehensive specification establishes rigorous criteria for rubber-sheathed flexible cables operating at medium voltages ranging from 0.6/1 kV to 20/35 kV.