[email protected]

armoured instrumentation cable

15 Min Read
BASKET SPREADER 750: Next-Generation Hoisting Cable Architecture The BASKET SPREADER 750 (3GSLTOE) represents a fundamental advancement in hoisting control cable design, specifically engineered for next-generation automated port crane systems operating under extreme environmental and operational constraints. Unlike the BASKET SPREADER 740's 300/500V AC specification, the 750 operates at 0.6/1kV AC with dual-voltage DC capability (0.9/1.8 kV)—a classification shift that enables: Higher power capacity – 2–3× greater amperage per conductor, enabling longer cable runs with lower voltage drop Medium-voltage infrastructure compatibility – Direct integration with port substation power distribution systems (0.6 kV = 600V three-phase industrial standard) DC dual-voltage operation – Simultaneous support for AC motor control and DC feedback/signaling circuits (0.9/1.8 kV DC margins) Extreme temperature capability – Operating range −50°C to +80°C (vs. SPREADER 740's −20°C to +60°C), addressing Arctic port terminals and tropical high-ambient scenarios Advanced insulation chemistry – GAALTHERM® 530 thermoplastic compound replaces standard PVC/PUR, delivering superior chemical resistance and thermal stability This cable bridges the gap between standard control cables (300/500V, limited temperature) and heavy industrial medium-voltage distribution cables, creating a purpose-built solution for modern automated gantry crane systems in global port terminals.
Technical Department
on12/06/2026

Что такое ÖLFLEX® INSTRUM RE-Y(ST)YRY: инженерный анализ армированного heat resistant PVC кабеля с общим экраном

ÖLFLEX® INSTRUM RE-Y(ST)YRY — это армированный heat resistant PVC instrumentation/data cable с PVC (V-90HT) core insulation, overall screen, PVC inner sheath, galvanized steel wire armour and PVC outer sheath. Кабель предназначен для communication, data and voice transmission signal в industrial process manufacturing plants, Oil and Gas industry and petrochemical industry. По предоставленным данным он основан на EN 50288-7, имеет flame retardance according to IEC 60332-3-24, stranded plain annealed copper wires according to BS 6360 / IEC 60228 Class 2, aluminium polyester tape collective screen, tinned copper drain wire, black PVC inner sheath and black or blue PVC outer sheath.
14 Min Read
LIFT-2S (European) vs. LIFT-1S UL (North American): LIFT-2S characteristics: Voltage: 300/500V (European standard, lower voltage) Temperature: −40°C to +70°C (moderate range) Standards: VDE 0482 part 265-2-1, EN 50265-2-1, IEC 60332-1-2 Design philosophy: Safety by material redundancy (2 steel cores) Steel cores: 2× cores provide mechanical backup Conductor: Class 6 (European, ~150–200 wires per mm²) Cost: Lower (proven European manufacturing) Market: Europe, Asia-Pacific, most of world LIFT-1S UL characteristics: Voltage: 600V (North American standard, higher voltage) Temperature: −25°C to +105°C (extreme range, high-temp optimized) Standards: UL 2562, UL 62, CSA C22.2 No.210.2 Design philosophy: Safety by certification (single core + redundant control) Steel core: 1× core (sufficient with nylon covering) Conductor: Class M (UL, extra fine ~300+ wires per mm²) Cost: Higher (UL testing, certification documentation) Market: North America (USA, Canada), Mexico UL 2562 specialty certification: UL 2562 scope: Elevator and Dumbwaiter Cables Specific requirements: 1. Pendant cable design (cable hangs freely, no duct support) 2. Vertical orientation (designed for gravity-loaded suspension) 3. Repeated flex cycles (cable moves up/down frequently) 4. Safety-critical function (failure = personnel risk) Consequence: More stringent than general-purpose cables Testing includes: Bend cycle fatigue, heat aging, compression resistance Test procedures (unique to UL 2562): Bend cycle test: 1,000+ cycles at minimum bending radius Cable must pass insulation resistance after cycling Heat aging: 500+ hours at 105°C continuous Tensile strength retention minimum 70% Compression: 1,000+ hours under sustained compression Cable cross-section must not exceed 5% permanent deformation LIFT-2S (no UL 2562): Tests per VDE are less stringent on fatigue/cycling Assumes cable mostly static, not repeated flex Adequate for European elevator duty (lower speed, fewer cycles) LIFT-1S UL: All UL 2562 tests passed (proven for North American elevators) Faster cycle times, more frequent motion → more fatigue stress Extra testing ensures reliability under North American elevator duty Market requirement (regulatory): Europe/International: CE mark required (European conformity) VDE/EN/IEC standards sufficient No UL certification needed (not recognized in EU) LIFT-2S is sufficient North America (USA, Canada): UL certification mandatory for elevators UL 2562 specifically for elevator cables CSA dual certification required in Canada LIFT-2S NOT acceptable (lacks UL 2562) LIFT-1S UL mandatory Cost implication: UL certification: ~$5,000–15,000 per product per region Testing duration: 3–6 months per model Documentation: Comprehensive test reports, technical files Result: LIFT-1S UL 20–30% higher cost than equivalent European cable
Technical Department
on12/06/2026

Что такое ÖLFLEX® INSTRUM RE-2X(ST)YRY: инженерный анализ армированного инструментального кабеля с XLPE изоляцией и общим экраном

ÖLFLEX® INSTRUM RE-2X(ST)YRY — это armoured instrumentation cable с XLPE core insulation, overall screen, PVC inner sheath, galvanized steel wire armour and PVC outer sheath. Кабель предназначен для communication, data and voice transmission signal в industrial process manufacturing plants, Oil and Gas industry and petrochemical industry. По предоставленным данным он основан на EN 50288-7, имеет flame retardance according to IEC 60332-3-24, stranded plain annealed copper wires according to BS 6360 / IEC 60228 Class 2, aluminium polyester tape collective screen, tinned copper drain wire, black PVC inner sheath and black or blue PVC outer sheath.
8 Min Read
EN 50288-7 instrumentation cables are multi-element metallic cables used in analogue and digital communication and control applications. Manufactured in accordance with European Standard EN 50288 (British Standard BS EN 50288), these cables are widely used in processing plants such as those found in the petrochemical industry due to their ability to withstand electromagnetic interference (EMI). They are specifically designed for the transmission of signals in instrumentation, control, and communication applications, commonly available in 300V and 500V voltage ratings.
Technical Department
on31/12/2025

What is EN 50288-7 Cable?

EN 50288-7 cable, BS EN 50288-7, instrumentation cable, control cable, RE-2X(st)H cable, RE-2X(st)Y cable, RE-2Y(st)Y cable, PiMF cable, TiMF cable, screened cable, petrochemical cable, XLPE instrumentation cable, LSZH instrumentation cable