[email protected]

Flexible Power Supply Cable

24 Min Read
When sourcing a flame-retardant alternative to Prysmian Type 7 1.1kV mining cables for use in Australian underground coal mines, the appropriate specification is AS/NZS 1802 Type 241 (1.1/1.1kV). The AS/NZS 1802 Type 241 cable provides complete electrical and mechanical compliance with Australian mining safety regulations, features enhanced flame-retardant properties through heavy-duty PCP or CPE elastomer sheathing, and employs a symmetrical earth conductor architecture that ensures precise earth leakage fault detection—a requirement that the original British BS 6708 Type 7 cannot satisfy. For heavy mechanized equipment such as continuous miners, Type 241 is the standard selection; for lighter handheld drilling equipment, AS/NZS 1802 Type 210 is often preferred. Type 241 delivers the same operational functionality as Type 7 while meeting the strict electrical safety requirements of the Australian Standards and the WorkSafe framework that governs underground coal mining operations.
Technical Department
on06/03/2026

Type 7 Equivalent: Sourcing Flame-Retardant Alternative for Prysmian Type 7 1.1kV Machine Cables

When sourcing a flame-retardant alternative to Prysmian Type 7 1.1kV mining cables for use in Australian underground coal mines, the appropriate specification is AS/NZS 1802 Type 241 (1.1/1.1kV). The AS/NZS 1802 Type 241 cable provides complete electrical and mechanical compliance with Australian mining safety regulations, features enhanced flame-retardant properties through heavy-duty PCP or CPE elastomer sheathing, and employs a symmetrical earth conductor architecture that ensures precise earth leakage fault detection—a requirement that the original British BS 6708 Type 7 cannot satisfy. For heavy mechanized equipment such as continuous miners, Type 241 is the standard selection; for lighter handheld drilling equipment, AS/NZS 1802 Type 210 is often preferred. Type 241 delivers the same operational functionality as Type 7 while meeting the strict electrical safety requirements of the Australian Standards and the WorkSafe framework that governs underground coal mining operations.
16 Min Read
Feichun AS/NZS 1972 Type 2S 3.3kV cables can serve as direct drop-in replacements for Olex Nexans Versolex Type 2S mining cables, provided that the specifications are matched cross-section for cross-section and that the installation environment confirms compliance with AS/NZS 1972 requirements. However, this replacement is not automatic or universal. It requires careful verification of your existing Olex cable specifications, comparison against Feichun's equivalent product line, validation of termination compatibility, and confirmation that your mining site's electrical protection systems (earth leakage relays, neutral earthing resistors, and protection settings) are appropriately configured for the replacement cable's impedance characteristics.
Technical Department
on06/03/2026

Drop-in SWA Replacement for Olex Versolex Type 2S 3.3kV Underground Power Cable

Feichun AS/NZS 1972 Type 2S 3.3kV cables can serve as direct drop-in replacements for Olex Nexans Versolex Type 2S mining cables, provided that the specifications are matched cross-section for cross-section and that the installation environment confirms compliance with AS/NZS 1972 requirements. However, this replacement is not automatic or universal. It requires careful verification of your existing Olex cable specifications, comparison against Feichun’s equivalent product line, validation of termination compatibility, and confirmation that your mining site’s electrical protection systems (earth leakage relays, neutral earthing resistors, and protection settings) are appropriately configured for the replacement cable’s impedance characteristics.
9 Min Read
Direct Answer: Standard (N)TSCGEWÖU cables based on DIN VDE 0250-813 are not compliant with AS/NZS 1802 underground coal mining standards. The non-compliance is not merely a matter of standard jurisdiction—it reflects fundamental physical and electrical differences in cable structure, particularly regarding pilot core design and semiconductive cradle technology. 直接答案：基于DIN VDE 0250-813的标准(N)TSCGEWÖU电缆不符合AS/NZS 1802井下煤矿标准。非合规性不仅仅是标准管辖权的问题——它反映了电缆结构的根本物理和电气差异，特别是关于导引线设计和半导体支架技术。 Consequence: Using (N)TSCGEWÖU cables on Australian or New Zealand underground coal mining equipment violates workplace safety regulations and mining electrical codes. It also renders the equipment's earth fault detection system non-functional, eliminating critical protection against explosion and electrical hazards.
Technical Department
on05/03/2026

Is (N)TSCGEWÖU Compliant with AS/NZS 1802 Coal Mining Standards? Understanding the Pilot Core Issue

Direct Answer: Standard (N)TSCGEWÖU cables based on DIN VDE 0250-813 are not compliant with AS/NZS 1802 underground coal mining standards. The non-compliance is not merely a matter of standard jurisdiction—it reflects fundamental physical and electrical differences in cable structure, particularly regarding pilot core design and semiconductive cradle technology. 直接答案：基于DIN VDE 0250-813的标准(N)TSCGEWÖU电缆不符合AS/NZS 1802井下煤矿标准。非合规性不仅仅是标准管辖权的问题——它反映了电缆结构的根本物理和电气差异，特别是关于导引线设计和半导体支架技术。 Consequence: Using (N)TSCGEWÖU cables on Australian or New Zealand underground coal mining equipment violates workplace safety regulations and mining electrical codes. It also renders the equipment’s earth fault detection system non-functional, eliminating critical protection against explosion and electrical hazards.
30 Min Read
A stacker-reclaimer at a Newcastle coal export facility began experiencing intermittent loss of load cell signals, causing the control system to alarm and sometimes force the equipment into manual operation. Initial inspection found no obvious cable damage, and preliminary multimeter continuity tests showed the pilot conductors intact. However, when the equipment was operated at full speed during testing, the pilot conductor resistance measurement jumped from approximately 8 ohms to 45 ohms, demonstrating clear intermittency. A TDR test located the fault at approximately 450 meters along a 600-meter cable run. Detailed microscopic analysis of a cable section removed from the fault location revealed fatigue-induced microfractures in multiple copper strands within the pilot core. The root cause was identified as excessive vibration from poorly lubricated reeling drum bearings. The cable was successfully spliced at the fault location using a mid-cable connector kit, and bearing maintenance was performed to address the underlying vibration problem. The repaired cable has since operated successfully for over three years without additional pilot core failures.
Technical Department
on26/02/2026

AS/NZS 1802 Type 440: Troubleshooting Pilot Core Continuity Failures on Long-Travel Stacker-Reclaimer Reeling Drums

A stacker-reclaimer at a Newcastle coal export facility began experiencing intermittent loss of load cell signals, causing the control system to alarm and sometimes force the equipment into manual operation. Initial inspection found no obvious cable damage, and preliminary multimeter continuity tests showed the pilot conductors intact. However, when the equipment was operated at full speed during testing, the pilot conductor resistance measurement jumped from approximately 8 ohms to 45 ohms, demonstrating clear intermittency. A TDR test located the fault at approximately 450 meters along a 600-meter cable run. Detailed microscopic analysis of a cable section removed from the fault location revealed fatigue-induced microfractures in multiple copper strands within the pilot core. The root cause was identified as excessive vibration from poorly lubricated reeling drum bearings. The cable was successfully spliced at the fault location using a mid-cable connector kit, and bearing maintenance was performed to address the underlying vibration problem. The repaired cable has since operated successfully for over three years without additional pilot core failures.
11 Min Read
Mining Cable
Technical Department
on11/11/2025

What is UNE 22510:1996 Mining Cables?

UNE 22510:1996 is a Spanish national standard published by the Spanish Association for Standardization and Certification (AENOR) that specifies comprehensive requirements for electric cables designed for underground mining operations. This standard, classified under ICS categories 29.060.20 (Cables) and 73.100.99 (Other mining equipment), establishes rigorous guidelines for cable construction, performance, and safety in hazardous mining environments.
19 Min Read
DIN VDE 0250 German Standard Flexible Power Reeling Cable
Technical Department
on10/11/2025

What is DIN VDE 0250 Reeling Cables?

DIN VDE 0250 represents the globally recognized German standard for flexible electrical cables designed specifically for cranes, material handling equipment, and mobile machinery applications. As Germany remains the only country to have issued special design regulations for flexible electrical cables covering cranes and material handling equipment, this standard has achieved worldwide acceptance as the ultimate benchmark for tough rubber-sheathed flexible reeling cables.