[email protected]

EAC certified cable

3 Min Read
H07RN-F: Advanced High-Flexibility Salt-Fog Resistant Port Cable Engineering Solution Specialized rubber-sheathed electrical cable engineered for extreme maritime and coastal port environments. H07RN-F combines superior mechanical flexibility (4×D minimum fixed-laying bending radius, 6×D flexible-application capability) with comprehensive salt-fog environmental resistance, enabling reliable 450/750V power distribution and control signaling in container gantry systems, ship loaders, and port automation infrastructure where conventional cables fail within 6–12 months of deployment.
Technical Department
on22/06/2026

机械设备出口欧俄总是卡关？飞纯电缆自带 CE+EAC+俄罗斯FSC，助你一站式通关！

机械设备出口欧盟、俄罗斯及欧亚市场，真正的难点往往不只在整机本体，而在整机内部那些容易被忽视的关键配套部件。电缆作为动力传输、控制信号、移动供电、安全联锁和消防风险控制的重要载体，一旦认证文件不完整、标识不匹配、消防证明缺失或与整机技术资料不一致，就可能成为清关、入库、项目验收和现场投运的卡点。飞纯电缆自带 CE、EAC 与俄罗斯 FSC 消防认证，以“欧盟合规 + 欧亚准入 + 俄罗斯消防”的组合能力，为机械设备出口提供更完整的一站式通关解决方案。
3 Min Read
Spreader Bar Cable Application: What is a spreader bar? Container crane context: Gantry crane positioned at dock Overhead hoist mechanism: Winch + trolley system Spreader bar: Attachment point below hoist Function: Grips container corners, distributes load, tilts container for placement Spreader bar structure: Framework: Steel tubes/beams forming rectangular frame Lifting points: 4 corner attachment rings (one per container corner) Electrical system: Motor-driven locks, position sensors, lighting Cables: Power supply for motors + control signals for locking mechanism Cable location (spreader bar): Vertical run (primary): From crane hoist (top) down 20–40 m to spreader bar (bottom) Function: Supply power for: - Corner lock solenoids (release container locks) - Position feedback sensors (confirm locks engaged) - Optional: Spreader bar lighting (visibility during operation) Simultaneous function: Act as partial mechanical support (share load with main hoist cable) Horizontal distribution (on spreader bar): From entry point distributed across spreader frame Supply all four corner lock motors Branching: May split into smaller branches (4× circuits to corners) Mechanical load: Cable must withstand: Static tension: Weight of container payload (20–40 tons distributed) Dynamic loads: Jerking during load acceleration, swinging in wind Thermal: Tropical port environment, direct sun, saltwater spray Abrasion: Rubbing against spreader frame during operation Cable design philosophy: Dual function (unique): Electrical function: Deliver 300/500V power for locking system Mechanical function: Share load-bearing (not primary structure, but support role) Different from: Pure electrical cables (festoon, lifting): Electrical function only Pure mechanical ropes: Mechanical function only BASKET SPREADER 730: Both functions integrated Speed specification rationale: 160 m/min (relatively slow): Container crane cycle time: ~45–60 seconds per lift Descent distance: 20–40 m Descent speed: 20–40 m ÷ 45–60 sec = 0.33–0.9 m/s = 20–54 m/min Average speed: ~30 m/min (loading) + 20 m/min (discharge) = 25 m/min 160 m/min specification: 6–8× safety margin on speed Design: Allows for fast emergency ascent if needed Why not higher speed? Mechanical load constraint: Heavy cable (4000 N = ~400 kg equivalent) Inertia: Accelerating 400 kg + spreader bar + container inertia takes time Structural: Crane frame limits acceleration rates (safety interlocks) Result: 160 m/min is practical maximum for loaded spreader bar
Technical Department
on22/06/2026

从欧盟到俄罗斯：飞纯风电电缆斩获 ATEX、IECEx 防爆与俄罗斯 FSC 消防双重硬核认证！

全球风电项目正在进入更严苛的安全合规时代。风机大型化、应用区域国际化、能源场景复合化，使风电电缆承担的责任远不止电力传输。它既要承受塔筒扭转、机舱振动、偏航运动、低温、潮湿、盐雾和油污等复杂环境，也要满足不同市场对防爆、防火、清关、验收和项目归档的高标准要求。飞纯风电电缆斩获 ATEX、IECEx 防爆认证与俄罗斯 FSC 消防认证，以“防爆 + 防火 + 国际合规”的硬核组合，为欧盟、国际工程和俄罗斯风电项目提供高安全等级电缆解决方案。
2 Min Read
H07BN4-F HAR Nomenclature Breakdown (per CEI 20-20/20-19): H = Harmonized standard designation (IEC 60227 compliance) Indicates cable meets international safety standards Full compatibility with European electrical regulations 07 = Voltage designation (Uo/U = 450/750V) 07 = 450/750V nominal voltage class (other classes: 03 = 300/500V, 04 = 400/690V) Testing: 3 kV test voltage (10 times nominal) B = Special feature (Flexible/Benign environment) B typically indicates bare or flexible conductor design (Standard = no letter designation) N = Rubber type designation N = Normally-proportioned sheath thickness (S = Slim/reduced, T = Thick/reinforced) For H07BN4-F: N = Standard thickness for 450/750V industrial use Insulation thickness: 1.2 mm per DIN VDE 0282 Sheath thickness: 1.0–1.5 mm per DIN VDE 0293 4 = Number of principal tests/features Typically indicates: (1) Temperature range, (2) Insulation type, (3) Sheath composition, (4) Mechanical properties certification F = Flexibility designation F = Fully flexible (can be wound on reels) (Other: S = Service-cord, C = Cable) H07BN4-F can be: Coiled on reel: Yes (reelable) Bent radius: Down to 4×D (normal use) to 2×D (close to terminal) Repeated winding: Yes (drum rating available) Continuous flexing: Yes (up to 50+ million cycles per EN 50266) HAR = Harmonics-compatible technology designation HAR = High-frequency harmonic and transient rated Specifically designed for: - VFD (variable frequency drive) motor circuits (up to 20 kHz switching) - Welding equipment (high current transients, multi-frequency content) - Industrial power electronics environments (distorted waveforms) HAR testing per EN 50334: Transient overvoltage withstand: 3× nominal voltage, sustained Harmonic content up to 50th harmonic: Fully rated Dv/dt immunity: >3 kV/µs (fast switching events) Comparison: Standard vs. HAR designation Standard H07BN4-F (without HAR): Frequency: Single 50/60 Hz only Total harmonic distortion (THD) limit: 20% acceptable (VFD typical) Transient immunity: Enhanced (3+ kV nominal test) Suitable for: VFD motors, welding, power electronics Cost: +8–12% premium over standard Application advantage: Single cable type serves both conventional and VFD circuits
Technical Department
on22/06/2026

集齐 VDE、CE、UKCA、EAC！飞纯 H07BN4-F 欧标风电扭缆开启全球通关模式

风电项目正在从单一区域交付走向全球化配套。对风机制造商、EPC、设备集成商和出口项目来说，电缆不仅要能承受塔筒扭转、机舱振动、低温环境和长期运行，更要具备清晰的认证文件与市场准入能力。飞纯 H07BN4-F 欧标风电扭缆集齐 VDE、CE、UKCA、EAC 多重认证，为风电设备出口、海外项目投标和多区域交付提供更高效的合规支撑。
33 Min Read
Когда инженер или менеджер по закупкам впервые сталкивается с задачей импорта иностранного электрического кабеля в Россию, он часто наталкивается на путаницу, которая легко может привести к дорогостоящим ошибкам. Есть соблазн думать, что техническое совпадение со стандартом VDE или IEC — это всё, что требуется. Однако в действительности существуют три полностью независимых и параллельных требования, которые должны быть удовлетворены одновременно. Давайте разберём их как систему взаимосвязанных компонентов, которая работает подобно многоуровневой фильтрации. Первый уровень: Техническое соответствие стандартам (ГОСТ, VDE или IEC) На этом уровне кабель должен удовлетворять электрическим и механическим параметрам, которые установлены в соответствующем национальном стандарте. Для немецкого кабеля это означает соответствие VDE 0250-813 — толщина изоляции, токоведущая способность жил, испытательные напряжения, механическая прочность оболочки. Эти параметры проверяются в испытательной лаборатории и документируются в протоколах испытаний. Если техническое соответствие не доказано, кабель не может быть использован, однако чисто теоретически кабель может быть физически доставлен на склад.
Technical Department
on11/03/2026

EAC Certified VDE Cables: Sourcing (N)TSCGEWÖU 3×50+3×25/3 with TR CU 004/2011 ComplianceComplete Regulatory & Procurement Guide

Когда инженер или менеджер по закупкам впервые сталкивается с задачей импорта иностранного электрического кабеля в Россию, он часто наталкивается на путаницу, которая легко может привести к дорогостоящим ошибкам. Есть соблазн думать, что техническое совпадение со стандартом VDE или IEC — это всё, что требуется. Однако в действительности существуют три полностью независимых и параллельных требования, которые должны быть удовлетворены одновременно. Давайте разберём их как систему взаимосвязанных компонентов, которая работает подобно многоуровневой фильтрации. Первый уровень: Техническое соответствие стандартам (ГОСТ, VDE или IEC) На этом уровне кабель должен удовлетворять электрическим и механическим параметрам, которые установлены в соответствующем национальном стандарте. Для немецкого кабеля это означает соответствие VDE 0250-813 — толщина изоляции, токоведущая способность жил, испытательные напряжения, механическая прочность оболочки. Эти параметры проверяются в испытательной лаборатории и документируются в протоколах испытаний. Если техническое соответствие не доказано, кабель не может быть использован, однако чисто теоретически кабель может быть физически доставлен на склад.
23 Min Read
KGE-HL (КГЭ-ХЛ) 3x35+1x10 6kV Siberian mining cable, which represents a three-conductor power cable with a 1×10 mm² uninsulated grounding conductor, achieves a maximum static operating temperature of -60°C (−76°F) and undergoes dynamic cold bend testing at -40°C (−40°F) according to GOST 24334-80 specifications. This testing temperature of -40°C represents a critical threshold: at this temperature, the synthetic rubber jacketing remains flexible enough to withstand the mechanical stress of being wound on cable drums, reeled and unreeled by excavator equipment, and subjected to dynamic bending without developing cracks or permanent deformation. The designation "HL" (ХЛ in Cyrillic) stands for "Kholodostoyky" or "Cold-Resistant," indicating that the cable has been specifically engineered and tested to maintain electrical integrity and mechanical durability in the extreme Arctic and sub-Arctic conditions found in Siberian mining operations. The cable's maximum allowable continuous operating temperature is +50°C (122°F) under normal installation conditions, with the three copper power conductors rated for a maximum continuous conductor temperature of +75°C (167°F). These temperature ratings define the envelope within which the cable can operate safely over its service life without degradation of the insulation, jacketing, or shielding materials. The 3×35 mm² designation refers to the three power conductors, each with a cross-sectional area of 35 square millimeters, providing substantial current-carrying capacity suitable for powering large excavation equipment. The 1×10 mm² component designates an uninsulated grounding conductor that runs directly in contact with the cable's semiconductive shielding layer, enabling rapid grounding and fault protection. Understanding how this cable maintains mechanical flexibility at temperatures where conventional industrial cables become dangerously brittle is essential for mining engineers, equipment operators, and safety managers evaluating cable selection for Arctic operations.
Technical Department
on28/02/2026

Cold Bend Testing (-40°C): Minimum Operating Temperature for KGE-HL 3×35+1×10 6kV Siberian Mining Cable

KGE-HL (КГЭ-ХЛ) 3×35+1×10 6kV Siberian mining cable, which represents a three-conductor power cable with a 1×10 mm² uninsulated grounding conductor, achieves a maximum static operating temperature of -60°C (−76°F) and undergoes dynamic cold bend testing at -40°C (−40°F) according to GOST 24334-80 specifications. This testing temperature of -40°C represents a critical threshold: at this temperature, the synthetic rubber jacketing remains flexible enough to withstand the mechanical stress of being wound on cable drums, reeled and unreeled by excavator equipment, and subjected to dynamic bending without developing cracks or permanent deformation. The designation “HL” (ХЛ in Cyrillic) stands for “Kholodostoyky” or “Cold-Resistant,” indicating that the cable has been specifically engineered and tested to maintain electrical integrity and mechanical durability in the extreme Arctic and sub-Arctic conditions found in Siberian mining operations. The cable’s maximum allowable continuous operating temperature is +50°C (122°F) under normal installation conditions, with the three copper power conductors rated for a maximum continuous conductor temperature of +75°C (167°F). These temperature ratings define the envelope within which the cable can operate safely over its service life without degradation of the insulation, jacketing, or shielding materials. The 3×35 mm² designation refers to the three power conductors, each with a cross-sectional area of 35 square millimeters, providing substantial current-carrying capacity suitable for powering large excavation equipment. The 1×10 mm² component designates an uninsulated grounding conductor that runs directly in contact with the cable’s semiconductive shielding layer, enabling rapid grounding and fault protection. Understanding how this cable maintains mechanical flexibility at temperatures where conventional industrial cables become dangerously brittle is essential for mining engineers, equipment operators, and safety managers evaluating cable selection for Arctic operations.
5 Min Read
PROTOMONT(Z) NSSHKCGEOEU 0.6/1KV is a coal cutter cable designed for free trailing operations in underground mining applications, used as power supply connection cable for mobile equipment such as coal shearers, roadheaders, TBMs, or scoops (LHDs). The (Z) Coal-Cutter cables are specifically designed for free trailing operation and, due to their special galvanized steel wire braiding construction, may be trailed for considerable distances behind the machine during operation. Features very finely stranded tinned copper conductors (Class FS), EPR rubber insulation (PROTOLON 3GI3), galvanized steel wire braiding armour, and polychloroprene (PCP) outer sheath (PROTOFIRM 5GM5). Offers up to 36,000N tensile strength and 150m/min travel speed. Certified by MSHA P-189-4, EAC, and Bosnia-Herzegovina BAS.
Technical Department
on14/01/2026

كابل PROTOMONT(Z) NSSHKCGEOEU 0,6/1KVكابلات قاطعات الفحم لعمليات السحب الحر – التعدين تحت الأرض

PROTOMONT(Z) NSSHKCGEOEU 0.6/1KV 是專為地下採礦作業中的自由拖曳操作設計的採煤機電纜，用於連接採煤機、掘進機、隧道掘進機(TBM)或鏟運機(LHD)等移動設備。(Z)型採煤機電纜專為自由拖曳操作設計，由於其特殊的鍍鋅鋼絲編織結構，可在設備後方拖曳相當長的距離。該電纜採用極細絞鍍錫銅導體（FS類）、EPR橡膠絕緣（PROTOLON 3GI3）、鍍鋅鋼絲編織鎧裝、氯丁橡膠外護套（PROTOFIRM 5GM5）。具有高達36,000N的拉伸強度和150m/min的移動速度。獲得MSHA P-189-4、EAC及波黑BAS等國際認證。
5 Min Read
PROTOMONT (V) NSSHCGEOEU LWL series represents advanced power transmission solutions engineered specifically for the demanding underground mining environment. These cables serve as power supply connections for coal cutting machines, continuous miners, and other mobile equipment. The "(V)" designation indicates cables designed for use in cable protection chains (cable handlers) that trail behind machinery and absorb substantial tensile forces during operation.
Technical Department
on16/12/2025

PROTOMONT (V) NSSHCGEOEU LWL 0.6/1KV

PROTOMONT (V) NSSHCGEOEU LWL series represents advanced power transmission solutions engineered specifically for the demanding underground mining environment. These cables serve as power supply connections for coal cutting machines, continuous miners, and other mobile equipment. The “(V)” designation indicates cables designed for use in cable protection chains (cable handlers) that trail behind machinery and absorb substantial tensile forces during operation.
4 Min Read
PROTOMONT(Z) NSSHCGEOEU 0.6/1KV coal cutter cable represents the pinnacle of engineering for underground mining operations. These cables are specifically designed as power supply connection cables for mobile equipment in underground machine applications. (Z)-Coal-Cutter cables are engineered for free trailing operation and, due to their special construction, may be trailed for considerable distances behind the machine during operation. The robust design ensures reliable power transmission even under extreme mechanical stress conditions encountered in mining environments. Primary applications include coal shearers, roadheaders, tunnel boring machines (TBMs), and load-haul-dump vehicles (LHDs/scoops). The cable's exceptional flexibility and durability make it indispensable for modern mining operations worldwide.
Technical Department
on15/12/2025

PROTOMONT(Z) NSSHCGEOEU0.6/1KV Coal Cutter Cables

PROTOMONT(Z) NSSHCGEOEU 0.6/1KV coal cutter cable represents the pinnacle of engineering for underground mining operations. These cables are specifically designed as power supply connection cables for mobile equipment in underground machine applications. (Z)-Coal-Cutter cables are engineered for free trailing operation and, due to their special construction, may be trailed for considerable distances behind the machine during operation. The robust design ensures reliable power transmission even under extreme mechanical stress conditions encountered in mining environments. Primary applications include coal shearers, roadheaders, tunnel boring machines (TBMs), and load-haul-dump vehicles (LHDs/scoops). The cable’s exceptional flexibility and durability make it indispensable for modern mining operations worldwide.
3 Min Read
PROTOMONT(Z) NSSHKCGEOEU represents a highly specialized category of coal cutter cables engineered for free trailing operation in underground mining environments. The "(Z)" designation indicates this cable is specifically designed for trailing applications, where it must be trailed for considerable distances behind mobile mining machinery during operation. Unlike standard industrial cables, these are constructed to withstand extreme mechanical stresses including repeated bending, high tensile forces, impact, and crushing loads commonly encountered in coal mining operations.
Technical Department
on15/12/2025

PROTOMONT(Z) NSSHKCGEOEU 0.6/1KV Coal Cutter Cables for Trailing Operations

PROTOMONT(Z) NSSHKCGEOEU represents a highly specialized category of coal cutter cables engineered for free trailing operation in underground mining environments. The “(Z)” designation indicates this cable is specifically designed for trailing applications, where it must be trailed for considerable distances behind mobile mining machinery during operation. Unlike standard industrial cables, these are constructed to withstand extreme mechanical stresses including repeated bending, high tensile forces, impact, and crushing loads commonly encountered in coal mining operations.