[email protected]

CIF mining cable

16 Min Read
The AS/NZS 1802 Type 241 3x35mm² 1.1kV mining cable has a total weight of approximately 2,980 kilograms per kilometer, with copper content contributing roughly 1,500 kilograms per kilometer of that total. This cable has a 43.1 millimeter nominal outer diameter (tolerance range 41.5–44.5mm), carries an ampacity rating of 147 amperes in free air at 90°C conductor temperature, and is constructed from three 35mm² power conductors, three 16mm² interstitial grounding conductors, and one 16mm² central extensible pilot conductor (the latter typically used for remote control signaling in mining equipment). The cable is built to AS/NZS 1802 standard using EPR (ethylene propylene rubber) insulation and heavy-duty HD-85-PCP (polychloroprene) outer sheath, making it ideally suited for the extreme mechanical and thermal stresses of underground coal mining trailing cable applications—continuous miners, pump power supplies, and general mining equipment feeder systems. However, this specification applies exclusively to authentic AS/NZS 1802 Type 241 cables. Understanding this distinction is critical because many engineers and procurement teams encounter confusion when they search for "Olex Type 241" or "Versolex Type 241 equivalent," terms that conflate two fundamentally different product families with completely different material systems, standards, and field applications.
Technical Department
on05/03/2026

AS/NZS 1802 Type 241 3x35mm² 1.1kV Weight Calculator: Complete Specifications and Why Versolex Is Not Type 241

The AS/NZS 1802 Type 241 3x35mm² 1.1kV mining cable has a total weight of approximately 2,980 kilograms per kilometer, with copper content contributing roughly 1,500 kilograms per kilometer of that total. This cable has a 43.1 millimeter nominal outer diameter (tolerance range 41.5–44.5mm), carries an ampacity rating of 147 amperes in free air at 90°C conductor temperature, and is constructed from three 35mm² power conductors, three 16mm² interstitial grounding conductors, and one 16mm² central extensible pilot conductor (the latter typically used for remote control signaling in mining equipment). The cable is built to AS/NZS 1802 standard using EPR (ethylene propylene rubber) insulation and heavy-duty HD-85-PCP (polychloroprene) outer sheath, making it ideally suited for the extreme mechanical and thermal stresses of underground coal mining trailing cable applications—continuous miners, pump power supplies, and general mining equipment feeder systems. However, this specification applies exclusively to authentic AS/NZS 1802 Type 241 cables. Understanding this distinction is critical because many engineers and procurement teams encounter confusion when they search for “Olex Type 241” or “Versolex Type 241 equivalent,” terms that conflate two fundamentally different product families with completely different material systems, standards, and field applications.
24 Min Read
The dielectric constant of the 3GI3 elastomeric insulation used in (N)3GHSSYCY 3x150+3x25/3 cable is approximately 6.2 to 6.8 at standard reference frequency of 1 kHz, with typical measured value around 6.5 for new cable material. The insulation breakdown voltage (also called dielectric strength or withstand voltage) exceeds 30 kV when measured under controlled laboratory conditions on fresh cable samples with 8 mm insulation thickness, typically achieving 32–38 kV before electrical breakdown occurs.
Technical Department
on27/02/2026

Dielectric Constant Specs: What is the exact dielectric constant and insulation breakdown voltage for (N)3GHSSYCY 3×150+3×25/3 medium-voltage cable in long VFD motor runs? 

The dielectric constant of the 3GI3 elastomeric insulation used in (N)3GHSSYCY 3×150+3×25/3 cable is approximately 6.2 to 6.8 at standard reference frequency of 1 kHz, with typical measured value around 6.5 for new cable material. The insulation breakdown voltage (also called dielectric strength or withstand voltage) exceeds 30 kV when measured under controlled laboratory conditions on fresh cable samples with 8 mm insulation thickness, typically achieving 32–38 kV before electrical breakdown occurs.
17 Min Read
Type SHD-GC 3/C #1 AWG 8kV trailing cable is approximately 0.410 Ohms/km at 20°C reference temperature for a single conductor, calculated from the copper's material resistivity combined with the #1 AWG conductor cross-section (approximately 42.4 mm² or 53,486 circular mils). This resistance value increases to approximately 0.495 Ohms/km at 90°C operating temperature due to copper's positive temperature coefficient of resistance. For a complete three-phase circuit using this cable type, the total circuit resistance including all three phase conductors but excluding the ground return path is approximately 0.410 Ohms/km at 20°C or 0.495 Ohms/km at 90°C. When operating a mine shovel or dragline drawing 150–160 amperes over a typical 1,000-meter (1 km) cable run from the mine substation to the equipment, the three-phase voltage drop across this cable is approximately 55–70 volts at the reference condition, representing a drop of roughly 0.75–1.0% from the 8,000-volt nominal supply. This voltage drop magnitude is acceptable for most mining equipment applications and remains within typical power system design standards that permit up to 2–3% voltage drop on secondary feeder circuits. The physical mechanism behind this resistance is the collision of free electrons within the copper lattice structure, where random thermal motion of atoms creates an effective "friction" that opposes electron flow, converting electrical energy into heat at a rate proportional to I²R.
Technical Department
on27/02/2026

Voltage Drop Calculation: What is the DC resistance (Ohms/km) for Type SHD-GC 3/C #1 AWG 8kV trailing cable? 

Type SHD-GC 3/C #1 AWG 8kV trailing cable is approximately 0.410 Ohms/km at 20°C reference temperature for a single conductor, calculated from the copper’s material resistivity combined with the #1 AWG conductor cross-section (approximately 42.4 mm² or 53,486 circular mils). This resistance value increases to approximately 0.495 Ohms/km at 90°C operating temperature due to copper’s positive temperature coefficient of resistance. For a complete three-phase circuit using this cable type, the total circuit resistance including all three phase conductors but excluding the ground return path is approximately 0.410 Ohms/km at 20°C or 0.495 Ohms/km at 90°C. When operating a mine shovel or dragline drawing 150–160 amperes over a typical 1,000-meter (1 km) cable run from the mine substation to the equipment, the three-phase voltage drop across this cable is approximately 55–70 volts at the reference condition, representing a drop of roughly 0.75–1.0% from the 8,000-volt nominal supply. This voltage drop magnitude is acceptable for most mining equipment applications and remains within typical power system design standards that permit up to 2–3% voltage drop on secondary feeder circuits. The physical mechanism behind this resistance is the collision of free electrons within the copper lattice structure, where random thermal motion of atoms creates an effective “friction” that opposes electron flow, converting electrical energy into heat at a rate proportional to I²R.