[email protected]

AWG mining cable equivalent

2 Min Read
The Design Temperature Assumption: AS/NZS 1802 mining cable standards were developed for Australian and New Zealand mining conditions, where minimum ambient temperatures rarely drop below -10°C to -15°C. The standard's base material specifications (PCP chloroprene jacket, standard EPR insulation) were formulated for this relatively temperate range. A cable certified to AS/NZS 1802 specifications is guaranteed to function correctly from 0°C to 60°C (typical service range), with an operating floor around -20°C at absolute minimum. AS/NZS 1802矿用电缆标准是为澳大利亚和新西兰矿业条件而开发的，最低环境温度很少低于-10°C至-15°C。该标准的基础材料规范(PCP氯丁橡胶护套、标准EPR绝缘)针对这个相对温暖的范围而配制。根据AS/NZS 1802规范认证的电缆保证在0°C至60°C范围内正确工作，绝对最低工作温度约为-20°C。
Technical Department
on06/03/2026

Cold Bend Performance: Modifying AS/NZS Mining Cables for -40°C Operation in Mongolia

The Design Temperature Assumption: AS/NZS 1802 mining cable standards were developed for Australian and New Zealand mining conditions, where minimum ambient temperatures rarely drop below -10°C to -15°C. The standard’s base material specifications (PCP chloroprene jacket, standard EPR insulation) were formulated for this relatively temperate range. A cable certified to AS/NZS 1802 specifications is guaranteed to function correctly from 0°C to 60°C (typical service range), with an operating floor around -20°C at absolute minimum. AS/NZS 1802矿用电缆标准是为澳大利亚和新西兰矿业条件而开发的，最低环境温度很少低于-10°C至-15°C。该标准的基础材料规范(PCP氯丁橡胶护套、标准EPR绝缘)针对这个相对温暖的范围而配制。根据AS/NZS 1802规范认证的电缆保证在0°C至60°C范围内正确工作，绝对最低工作温度约为-20°C。
19 Min Read
For a Type 3S 11kV feeder cable with 82–88 mm outer diameter (typically a 3x95mm² to 3x240mm² conductor), the appropriate Ex d cable gland must be sized to accommodate the cable's full outer diameter while maintaining the flange-threaded sealing design required by ATEX EN 60079-1 for Zone 1 explosive atmospheres. A typical selection for a 3x95mm² Type 3S cable would be an M100 or M105 flange-threaded gland rated for ATEX II 2G Ex d IIB T4, with a compressive sealing ring (typically 2 mm thick polyurethane or equivalent elastomer) that creates a pressure-tight barrier against explosive gas ingress, and a separate earthing screw or braided conductor that bonds the cable's steel wire armor directly to the enclosure's earth continuity. This is not simply a matter of finding any cable gland that fits the cable diameter—it is a critical safety component that must be certified, specified, and installed with precision.
Technical Department
on06/03/2026

Ex d Gland Matching: Terminating Type 3S 11kV SWA Armor in Hazardous Zone 1

For a Type 3S 11kV feeder cable with 82–88 mm outer diameter (typically a 3x95mm² to 3x240mm² conductor), the appropriate Ex d cable gland must be sized to accommodate the cable’s full outer diameter while maintaining the flange-threaded sealing design required by ATEX EN 60079-1 for Zone 1 explosive atmospheres. A typical selection for a 3x95mm² Type 3S cable would be an M100 or M105 flange-threaded gland rated for ATEX II 2G Ex d IIB T4, with a compressive sealing ring (typically 2 mm thick polyurethane or equivalent elastomer) that creates a pressure-tight barrier against explosive gas ingress, and a separate earthing screw or braided conductor that bonds the cable’s steel wire armor directly to the enclosure’s earth continuity. This is not simply a matter of finding any cable gland that fits the cable diameter—it is a critical safety component that must be certified, specified, and installed with precision.
10 Min Read
The Single Most Important Cable Design Decision in Underground Coal Mining: Whether the cable employs collective screening (Type 2) or individual phase screening (Type 2S). This single engineering choice directly determines whether a mechanical cable failure will result in a phase-to-earth fault (detected and stopped in milliseconds) or a phase-to-phase fault with thousands of amperes of arc current (igniting methane explosions).
Technical Department
on06/03/2026

Type 2 vs Type 2S: Why the “S” (Individual Screen) is Mandatory for 11kV Underground Coal Mines

The Single Most Important Cable Design Decision in Underground Coal Mining: Whether the cable employs collective screening (Type 2) or individual phase screening (Type 2S). This single engineering choice directly determines whether a mechanical cable failure will result in a phase-to-earth fault (detected and stopped in milliseconds) or a phase-to-phase fault with thousands of amperes of arc current (igniting methane explosions).