[email protected]

AC resistance

15 Min Read
LIFT-2S (European) vs. LIFT-1S UL (North American): LIFT-2S characteristics: Voltage: 300/500V (European standard, lower voltage) Temperature: −40°C to +70°C (moderate range) Standards: VDE 0482 part 265-2-1, EN 50265-2-1, IEC 60332-1-2 Design philosophy: Safety by material redundancy (2 steel cores) Steel cores: 2× cores provide mechanical backup Conductor: Class 6 (European, ~150–200 wires per mm²) Cost: Lower (proven European manufacturing) Market: Europe, Asia-Pacific, most of world LIFT-1S UL characteristics: Voltage: 600V (North American standard, higher voltage) Temperature: −25°C to +105°C (extreme range, high-temp optimized) Standards: UL 2562, UL 62, CSA C22.2 No.210.2 Design philosophy: Safety by certification (single core + redundant control) Steel core: 1× core (sufficient with nylon covering) Conductor: Class M (UL, extra fine ~300+ wires per mm²) Cost: Higher (UL testing, certification documentation) Market: North America (USA, Canada), Mexico UL 2562 specialty certification: UL 2562 scope: Elevator and Dumbwaiter Cables Specific requirements: 1. Pendant cable design (cable hangs freely, no duct support) 2. Vertical orientation (designed for gravity-loaded suspension) 3. Repeated flex cycles (cable moves up/down frequently) 4. Safety-critical function (failure = personnel risk) Consequence: More stringent than general-purpose cables Testing includes: Bend cycle fatigue, heat aging, compression resistance Test procedures (unique to UL 2562): Bend cycle test: 1,000+ cycles at minimum bending radius Cable must pass insulation resistance after cycling Heat aging: 500+ hours at 105°C continuous Tensile strength retention minimum 70% Compression: 1,000+ hours under sustained compression Cable cross-section must not exceed 5% permanent deformation LIFT-2S (no UL 2562): Tests per VDE are less stringent on fatigue/cycling Assumes cable mostly static, not repeated flex Adequate for European elevator duty (lower speed, fewer cycles) LIFT-1S UL: All UL 2562 tests passed (proven for North American elevators) Faster cycle times, more frequent motion → more fatigue stress Extra testing ensures reliability under North American elevator duty Market requirement (regulatory): Europe/International: CE mark required (European conformity) VDE/EN/IEC standards sufficient No UL certification needed (not recognized in EU) LIFT-2S is sufficient North America (USA, Canada): UL certification mandatory for elevators UL 2562 specifically for elevator cables CSA dual certification required in Canada LIFT-2S NOT acceptable (lacks UL 2562) LIFT-1S UL mandatory Cost implication: UL certification: ~$5,000–15,000 per product per region Testing duration: 3–6 months per model Documentation: Comprehensive test reports, technical files Result: LIFT-1S UL 20–30% higher cost than equivalent European cable
Technical Department
on15/06/2026

Техническая информация PANZERFLEX: монтаж, эксплуатация, радиусы изгиба, кабельные барабаны и электрические расчёты

Данный технический раздел объединяет ключевые рекомендации по обращению, хранению, монтажу и электрическому расчёту гибких мобильных кабелей PANZERFLEX, PANZERLITE, PANZERFLAT, PANZERFLEX-ELX и BASKETHEAVYFLEX. Его задача — дать инженеру, проектировщику и монтажной команде практическую основу для правильного выбора cable handling system, расчёта bending radius, настройки tension protection, выбора cable reel, устранения twist, проверки current carrying capacity, short circuit current и voltage drop.
13 Min Read
(N)TSCGEWÖU Nomenclature Breakdown: (N) = "Nennspannung" (Nominal voltage designation) Indicates multi-voltage family (3.6/6 kV baseline, expandable to 20/35 kV) T = "Drei" implicitly (Three-phase implied in TSC configuration) SC = "S" (Stromleiter? Schirmung? Sheath-related) "C" (Conductor classification, typically Class 5 flexibility) Together: Three-core conductor family designation GE = "Gummi Elastomer" (Rubber Elastomer) Explicitly denotes EPR insulation (not polyethylene, not XLPE) German standard preference: EPR for MV reeling (vs. XLPE for fixed cables) WÖU = "Werkstoff/Öl/Umlauf" (Material/Oil/Circulation?) OR historically: VDE/UL approval markers? Likely: W = Werkstoff (special material formulation) Ö = Öl-resistenz (oil resistance capability) U = Universal or Umlauf (circulation/reeling capability) Combined meaning: (N)TSCGEWÖU = "Nominal-voltage Three-phase Single-conductor-core family, Gummi Elastomer insulation, Werkstoff-spezial (special material), Oil-resistant, Universal reeling" Design Philosophy Encoded: - Modular voltage architecture (one design, 3.6–20/35 kV options) - Three-phase power + distributed earth (TSC = not symmetric 3+3, but mixed) - EPR elastomer base (not synthetic XLPE) - Enhanced material formulation (not commodity grade) - Mobile/reeling-centric (forced guidance compatible) - Multi-environment tolerance (oil, moisture, temperature extremes)
Technical Department
on12/05/2026

(N)TSCGEWÖU Mining Trailing Cable

(N)TSCGEWÖU Nomenclature Breakdown: (N) = “Nennspannung” (Nominal voltage designation) Indicates multi-voltage family (3.6/6 kV baseline, expandable to 20/35 kV) T = “Drei” implicitly (Three-phase implied in TSC configuration) SC = “S” (Stromleiter? Schirmung? Sheath-related) “C” (Conductor classification, typically Class 5 flexibility) Together: Three-core conductor family designation GE = “Gummi Elastomer” (Rubber Elastomer) Explicitly denotes EPR insulation (not polyethylene, not XLPE) German standard preference: EPR for MV reeling (vs. XLPE for fixed cables) WÖU = “Werkstoff/Öl/Umlauf” (Material/Oil/Circulation?) OR historically: VDE/UL approval markers? Likely: W = Werkstoff (special material formulation) Ö = Öl-resistenz (oil resistance capability) U = Universal or Umlauf (circulation/reeling capability) Combined meaning: (N)TSCGEWÖU = “Nominal-voltage Three-phase Single-conductor-core family, Gummi Elastomer insulation, Werkstoff-spezial (special material), Oil-resistant, Universal reeling” Design Philosophy Encoded: – Modular voltage architecture (one design, 3.6–20/35 kV options) – Three-phase power + distributed earth (TSC = not symmetric 3+3, but mixed) – EPR elastomer base (not synthetic XLPE) – Enhanced material formulation (not commodity grade) – Mobile/reeling-centric (forced guidance compatible) – Multi-environment tolerance (oil, moisture, temperature extremes)