[email protected]

+90°C

7 Min Read
LIFT-2S (European) vs. LIFT-1S UL (North American): LIFT-2S characteristics: Voltage: 300/500V (European standard, lower voltage) Temperature: −40°C to +70°C (moderate range) Standards: VDE 0482 part 265-2-1, EN 50265-2-1, IEC 60332-1-2 Design philosophy: Safety by material redundancy (2 steel cores) Steel cores: 2× cores provide mechanical backup Conductor: Class 6 (European, ~150–200 wires per mm²) Cost: Lower (proven European manufacturing) Market: Europe, Asia-Pacific, most of world LIFT-1S UL characteristics: Voltage: 600V (North American standard, higher voltage) Temperature: −25°C to +105°C (extreme range, high-temp optimized) Standards: UL 2562, UL 62, CSA C22.2 No.210.2 Design philosophy: Safety by certification (single core + redundant control) Steel core: 1× core (sufficient with nylon covering) Conductor: Class M (UL, extra fine ~300+ wires per mm²) Cost: Higher (UL testing, certification documentation) Market: North America (USA, Canada), Mexico UL 2562 specialty certification: UL 2562 scope: Elevator and Dumbwaiter Cables Specific requirements: 1. Pendant cable design (cable hangs freely, no duct support) 2. Vertical orientation (designed for gravity-loaded suspension) 3. Repeated flex cycles (cable moves up/down frequently) 4. Safety-critical function (failure = personnel risk) Consequence: More stringent than general-purpose cables Testing includes: Bend cycle fatigue, heat aging, compression resistance Test procedures (unique to UL 2562): Bend cycle test: 1,000+ cycles at minimum bending radius Cable must pass insulation resistance after cycling Heat aging: 500+ hours at 105°C continuous Tensile strength retention minimum 70% Compression: 1,000+ hours under sustained compression Cable cross-section must not exceed 5% permanent deformation LIFT-2S (no UL 2562): Tests per VDE are less stringent on fatigue/cycling Assumes cable mostly static, not repeated flex Adequate for European elevator duty (lower speed, fewer cycles) LIFT-1S UL: All UL 2562 tests passed (proven for North American elevators) Faster cycle times, more frequent motion → more fatigue stress Extra testing ensures reliability under North American elevator duty Market requirement (regulatory): Europe/International: CE mark required (European conformity) VDE/EN/IEC standards sufficient No UL certification needed (not recognized in EU) LIFT-2S is sufficient North America (USA, Canada): UL certification mandatory for elevators UL 2562 specifically for elevator cables CSA dual certification required in Canada LIFT-2S NOT acceptable (lacks UL 2562) LIFT-1S UL mandatory Cost implication: UL certification: ~$5,000–15,000 per product per region Testing duration: 3–6 months per model Documentation: Comprehensive test reports, technical files Result: LIFT-1S UL 20–30% higher cost than equivalent European cable
Technical Department
on15/06/2026

PANZERFLEX-ELX MV — средневольтный барабанный кабель с двумя защитными жилами и элементом 60F

Гибкий кабель для горнодобывающего и перегрузочного оборудования, работающего при частых изгибах, кручении, быстрых перемещениях и значительных ускорениях. Представленная таблица относится к конфигурации 3 основные жилы + 2 разделённые защитные жилы + 1 дополнительный элемент 60F.
7 Min Read
BASKET SPREADER 740 (YSLTOE) is engineered specifically for hoisting and control applications where mechanical flexibility and electrical reliability must coexist in marine environments. Unlike load-bearing structural cables (which prioritize tensile strength), control cables emphasize: Conductor flexibility – Repeated bending over pulleys without mechanical fatigue Insulation integrity – Voltage breakdown resistance under salt-fog corrosion Mechanical damping – Rope-like flexibility to drape naturally in spreader bar frames Environmental barrier – Outer sheath blocks salt, moisture, and UV penetration Core Design Elements: Component Material Specification Function Port Environment Benefit Conductor Flexible red copper Class 6 (IEC 60228) Carries 300/500V power; enables bending flexibility High purity copper resists galvanic corrosion Insulation PVC type YI2 (IEC 60811) Electrical isolation; voltage breakdown resistance (2 kV test) PVC with marine additives prevents salt-induced tracking Central Unit Aramide yarns (Kevlar™ equivalent) Mechanical load-bearing backup; structural integrity Aramide resists moisture & salt; absorbs vibration stress Outer Sheath PUR type 11YM1 (DIN 73377) Environmental barrier; UV/ozone/moisture protection Superior salt-fog resistance; 20+ year marine lifespan
Technical Department
on15/06/2026

PANZERFLEX-ELX MV — гибкий средневольтный кабель для тяжёлых барабанных систем

PANZERFLEX-ELX MV — гибкий высоковольтный кабель для подключения подвижных частей машин и перегрузочного оборудования. Конструкция рассчитана на высокие и экстремальные механические нагрузки, частые изгибы и кручение, быстрые перемещения и сильные ускорения.
9 Min Read
EMC Performance Classification: EMC rating scale (VDE/EN standards): Basic: No shielding (part 813 unscreened) Fair: Partial coverage, 30–40 mm spacing in braid Good: 80–90% coverage, 95% coverage, all gaps 30 dB attenuation @ 500 kHz: >40 dB attenuation @ 5 MHz: >35 dB attenuation (typical peak range) Expected: Tinned copper braid achieves 35–50 dB across frequency range Immunity to external interference: Motor variable frequency drive (VFD) nearby: VFD RF emission: Typically 50–200 mV/m at cable distance Unshielded cable susceptibility: 100–500 mV induced noise Shielded cable (good EMC): 1–10 mV induced noise (50–100× reduction) Consequence: VFD-driven crane motor doesn't interfere with control signals No false triggering of safety systems Data integrity in digital control systems maintained Radiated immunity testing (per EN 61000-4-3): Test standard: Cable exposed to RF field 50 MHz–1 GHz Test field strength: 10 V/m typical Acceptance: No malfunction, signal corruption
Technical Department
on12/06/2026

ÖLFLEX® CHARGE EV-(R)EYU: техническая статья о кабеле для зарядки электромобилей

ÖLFLEX® CHARGE EV-(R)EYU — это гибкий кабель для conductive AC charging system electric vehicle. Кабель предназначен для зарядки electric vehicles and plug-in hybrid vehicles, подходит для indoor and outdoor use, имеет DEKRA & CQC approvals, стойкость к маслам, химическим веществам, UV, ozone, scraping and grinding, а также halogen-free and flame-retardant construction.
6 Min Read
GAALFLEX® VFD FE4(O)CR: 600V/1000V European Standard Cost-Optimized Variable Frequency Drive Cable with XLPE Insulation, Red Copper Braid-Only Shielding, PVC R2 Inner Sheath, Gray Special PVC Jacket, Exceptional +250°C Short-Circuit Tolerance, 3-Phase Industrial Motor, 2.5–300 mm² Flexible Class 5, 8×D Bending Radius, Enhanced EN 50266-2-4/IEC 60332-3-24 Flame Testing | European Cost-Optimized Industrial VFD Cable European standard 600V/1000V cost-optimized VFD cable combining XLPE (cross-linked polyethylene) insulation with advanced protection architecture including PVC R2 inner sheath, simplified red copper braid-only shielding, gray special PVC outer jacket, flexible Class 5 red copper, and professional industrial motor integration—addressing cost-sensitive industrial frequency converter specification (600V/1000V), standard temperature industrial environments with extended cold tolerance (−20/0 to +90°C), exceptional short-circuit fault tolerance (+250°C), simplified copper braid shielding with inner protection layer, extended motor spectrum (2.5–300 mm²), flexible motor routing (8×D bend radius), enhanced flame testing capability, and comprehensive European standard industrial automation infrastructure simultaneously.
Technical Department
on11/05/2026

GAALFLEX® VFD FE4(O)CR

GAALFLEX® VFD FE4(O)CR: 600V/1000V European Standard Cost-Optimized Variable Frequency Drive Cable with XLPE Insulation, Red Copper Braid-Only Shielding, PVC R2 Inner Sheath, Gray Special PVC Jacket, Exceptional +250°C Short-Circuit Tolerance, 3-Phase Industrial Motor, 2.5–300 mm² Flexible Class 5, 8×D Bending Radius, Enhanced EN 50266-2-4/IEC 60332-3-24 Flame Testing | European Cost-Optimized Industrial VFD Cable European standard 600V/1000V cost-optimized VFD cable combining XLPE (cross-linked polyethylene) insulation with advanced protection architecture including PVC R2 inner sheath, simplified red copper braid-only shielding, gray special PVC outer jacket, flexible Class 5 red copper, and professional industrial motor integration—addressing cost-sensitive industrial frequency converter specification (600V/1000V), standard temperature industrial environments with extended cold tolerance (−20/0 to +90°C), exceptional short-circuit fault tolerance (+250°C), simplified copper braid shielding with inner protection layer, extended motor spectrum (2.5–300 mm²), flexible motor routing (8×D bend radius), enhanced flame testing capability, and comprehensive European standard industrial automation infrastructure simultaneously.
6 Min Read
GAALFLEX® VFD FG7(O)CR: 600V/1000V European Standard Industrial Halogen-Free Variable Frequency Drive Cable with HEPR Rubber Insulation, Red Copper Braid-Only Shielding, PVC R2 Inner Sheath, Gray Special PVC Jacket, Exceptional +250°C Short-Circuit Tolerance, 3-Phase Industrial Motor, 2.5–300 mm² Flexible Class 5, 8×D Bending Radius, Enhanced EN 50266-2-4/IEC 60332-3-24 Flame Testing | European Halogen-Free Industrial VFD Cable European standard 600V/1000V halogen-free VFD cable combining HEPR (halogen-free ethylene propylene rubber) insulation with simplified red copper braid-only shielding, PVC R2 inner sheath, gray special PVC outer jacket, flexible Class 5 red copper, and professional industrial motor integration—addressing halogen-free industrial frequency converter specification (non-building-code), standard temperature industrial environments (−15/0 to +90°C), exceptional short-circuit fault tolerance (+250°C), simplified copper braid shielding topography, flexible motor routing (8×D bend radius), enhanced flame testing capability, and comprehensive European standard industrial automation infrastructure simultaneously.
Technical Department
on11/05/2026

Type FG7(O)CR GAALFLEX® VFD

GAALFLEX® VFD FG7(O)CR: 600V/1000V European Standard Industrial Halogen-Free Variable Frequency Drive Cable with HEPR Rubber Insulation, Red Copper Braid-Only Shielding, PVC R2 Inner Sheath, Gray Special PVC Jacket, Exceptional +250°C Short-Circuit Tolerance, 3-Phase Industrial Motor, 2.5–300 mm² Flexible Class 5, 8×D Bending Radius, Enhanced EN 50266-2-4/IEC 60332-3-24 Flame Testing | European Halogen-Free Industrial VFD Cable European standard 600V/1000V halogen-free VFD cable combining HEPR (halogen-free ethylene propylene rubber) insulation with simplified red copper braid-only shielding, PVC R2 inner sheath, gray special PVC outer jacket, flexible Class 5 red copper, and professional industrial motor integration—addressing halogen-free industrial frequency converter specification (non-building-code), standard temperature industrial environments (−15/0 to +90°C), exceptional short-circuit fault tolerance (+250°C), simplified copper braid shielding topography, flexible motor routing (8×D bend radius), enhanced flame testing capability, and comprehensive European standard industrial automation infrastructure simultaneously.
6 Min Read
GAALFLEX® VFD 1200: 600V/1000V European Standard Premium Variable Frequency Drive Cable with Proprietary GAALTHERM® 590 Premium Insulation, Extreme +250°C Short-Circuit Tolerance, UV-Resistant PUR Jacket, Aluminum Tape + Red Copper Wire Screen, 3-Phase Industrial Motor, 2.5–300 mm² Stranded Class 2, 8×D Minimum Bending Radius, −50/−40 to +90°C Temperature Range, Premium High-Performance Frequency Converter Integration | European Premium Industrial VFD Cable Premium European standard 600V/1000V high-performance VFD cable combining proprietary GAALTHERM® 590 premium insulation with exceptional electrical stability and exceptional +250°C short-circuit tolerance, stranded Class 2 red copper, aluminum tape + red copper wire screen, UV-resistant PUR outer jacket, and professional premium industrial motor integration—addressing premium high-performance frequency converter specification (600V/1000V), industrial motor control with exceptional fault tolerance, outdoor UV-resistant installation, flexible motor routing (8×D bend radius), hazardous-environment capability, and comprehensive European premium industrial automation infrastructure simultaneously.
Technical Department
on11/05/2026

GAALFLEX® VFD 1200

GAALFLEX® VFD 1200: 600V/1000V European Standard Premium Variable Frequency Drive Cable with Proprietary GAALTHERM® 590 Premium Insulation, Extreme +250°C Short-Circuit Tolerance, UV-Resistant PUR Jacket, Aluminum Tape + Red Copper Wire Screen, 3-Phase Industrial Motor, 2.5–300 mm² Stranded Class 2, 8×D Minimum Bending Radius, −50/−40 to +90°C Temperature Range, Premium High-Performance Frequency Converter Integration | European Premium Industrial VFD Cable Premium European standard 600V/1000V high-performance VFD cable combining proprietary GAALTHERM® 590 premium insulation with exceptional electrical stability and exceptional +250°C short-circuit tolerance, stranded Class 2 red copper, aluminum tape + red copper wire screen, UV-resistant PUR outer jacket, and professional premium industrial motor integration—addressing premium high-performance frequency converter specification (600V/1000V), industrial motor control with exceptional fault tolerance, outdoor UV-resistant installation, flexible motor routing (8×D bend radius), hazardous-environment capability, and comprehensive European premium industrial automation infrastructure simultaneously.