[email protected]

cable trench installation

21 Min Read
If you are an electrical engineer reviewing a Bill of Materials for a Kalimantan mining project and the BOM line reads "AS/NZS 1972 Type 2S 6.6kV 3×185mm² Armoured Cable," the cable you actually need is an AS/NZS 1972 Mine Feeder Cable rated 6.35/11kV, with 3×185mm² copper conductors, XLPE or EPR insulation, copper tape screen, and galvanised steel wire armour (SWA). The "Type 2S" designation on your BOM is technically incorrect for this voltage class—a point we will clarify in detail below—but the intent behind the specification is clear: a heavy-duty, armoured, medium-voltage power cable for primary distribution in an underground or open-pit mine. 如果您是一名审查加里曼丹矿区物料清单（BOM）的电气工程师，BOM 上写着"AS/NZS 1972 Type 2S 6.6kV 3×185mm² 铠装电缆"，您实际需要的是 AS/NZS 1972 矿用馈线电缆，额定 6.35/11kV，3×185mm² 铜导体，XLPE 或 EPR 绝缘，铜带屏蔽，镀锌钢丝铠装（SWA）。BOM 上的"Type 2S"标识在此电压等级下技术上不正确——我们将在下文详细说明——但规格的意图是明确的：用于矿井主干配电的重型铠装中压电力电缆。 The ampacity you should design around at 40°C ambient air temperature in Kalimantan is approximately 420 amperes for cable tray or free-air installation, and approximately 370 amperes for direct burial in tropical soil at 30°C ground temperature. These figures are derated from the standard 30°C base-case ampacity of approximately 460 A (air) and the 20°C base-case of approximately 400 A (ground), using the thermal derating methodology prescribed in AS/NZS 3008.1.1 and IEC 60502-2. The full derivation, including the governing equations and correction factors for Kalimantan's specific environmental conditions, follows in Sections 6 and 7.
Technical Department
on09/03/2026

AS/NZS 1972 Mine Feeder Cable 6.35/11kV 3×185mm² SWA: Ampacity Derating at 40°C for Kalimantan Coal and Nickel Mines

If you are an electrical engineer reviewing a Bill of Materials for a Kalimantan mining project and the BOM line reads “AS/NZS 1972 Type 2S 6.6kV 3×185mm² Armoured Cable,” the cable you actually need is an AS/NZS 1972 Mine Feeder Cable rated 6.35/11kV, with 3×185mm² copper conductors, XLPE or EPR insulation, copper tape screen, and galvanised steel wire armour (SWA). The “Type 2S” designation on your BOM is technically incorrect for this voltage class—a point we will clarify in detail below—but the intent behind the specification is clear: a heavy-duty, armoured, medium-voltage power cable for primary distribution in an underground or open-pit mine. 如果您是一名审查加里曼丹矿区物料清单（BOM）的电气工程师，BOM 上写着”AS/NZS 1972 Type 2S 6.6kV 3×185mm² 铠装电缆”，您实际需要的是 AS/NZS 1972 矿用馈线电缆，额定 6.35/11kV，3×185mm² 铜导体，XLPE 或 EPR 绝缘，铜带屏蔽，镀锌钢丝铠装（SWA）。BOM 上的”Type 2S”标识在此电压等级下技术上不正确——我们将在下文详细说明——但规格的意图是明确的：用于矿井主干配电的重型铠装中压电力电缆。 The ampacity you should design around at 40°C ambient air temperature in Kalimantan is approximately 420 amperes for cable tray or free-air installation, and approximately 370 amperes for direct burial in tropical soil at 30°C ground temperature. These figures are derated from the standard 30°C base-case ampacity of approximately 460 A (air) and the 20°C base-case of approximately 400 A (ground), using the thermal derating methodology prescribed in AS/NZS 3008.1.1 and IEC 60502-2. The full derivation, including the governing equations and correction factors for Kalimantan’s specific environmental conditions, follows in Sections 6 and 7.
8 Min Read
The selection of industrial power cables represents one of the most critical engineering decisions in drilling operations, whether on land or offshore. Two cable types dominate this application space: the Type SHD-GC （重型屏蔽接地检查电缆）, designed primarily for mobile mining and terrestrial drilling equipment, and the Type P （海洋平台电缆）, engineered specifically for harsh offshore and fixed platform environments. Though both cables operate at similar voltage ratings, they embody fundamentally different design philosophies that reflect the distinct mechanical, electrical, and safety demands of their respective application domains.
Technical Department
on25/02/2026

Type SHD-GC vs. Type P: Selecting the Right Trailing Cable for Land and Offshore Drilling 

The selection of industrial power cables represents one of the most critical engineering decisions in drilling operations, whether on land or offshore. Two cable types dominate this application space: the Type SHD-GC （重型屏蔽接地检查电缆）, designed primarily for mobile mining and terrestrial drilling equipment, and the Type P （海洋平台电缆）, engineered specifically for harsh offshore and fixed platform environments. Though both cables operate at similar voltage ratings, they embody fundamentally different design philosophies that reflect the distinct mechanical, electrical, and safety demands of their respective application domains.
7 Min Read
(N)TSKCGEWÖU specifications. This protective layer serves multiple critical functions within the cable assembly, with mechanical stress redistribution being among its most important roles. According to research published by Sibelco, the bedding compound is defined as the material applied around insulated conductors to maintain their position and provide bedding for protective armoring.[1] This layer functions as an intermediary component positioned between the laid-up cores and the metallic armor, creating what cable engineers describe as a separation sheath that fundamentally alters how mechanical forces are distributed throughout the cable structure.
Technical Department
on26/01/2026

Inner Sheath Function: Mechanical Stress Redistribution in (N)TSKCGEWÖU Cables

(N)TSKCGEWÖU specifications. This protective layer serves multiple critical functions within the cable assembly, with mechanical stress redistribution being among its most important roles. According to research published by Sibelco, the bedding compound is defined as the material applied around insulated conductors to maintain their position and provide bedding for protective armoring.[1] This layer functions as an intermediary component positioned between the laid-up cores and the metallic armor, creating what cable engineers describe as a separation sheath that fundamentally alters how mechanical forces are distributed throughout the cable structure.