[email protected]

45kN breaking load

6 Min Read
LIFT-2S (European) vs. LIFT-1S UL (North American): LIFT-2S characteristics: Voltage: 300/500V (European standard, lower voltage) Temperature: −40°C to +70°C (moderate range) Standards: VDE 0482 part 265-2-1, EN 50265-2-1, IEC 60332-1-2 Design philosophy: Safety by material redundancy (2 steel cores) Steel cores: 2× cores provide mechanical backup Conductor: Class 6 (European, ~150–200 wires per mm²) Cost: Lower (proven European manufacturing) Market: Europe, Asia-Pacific, most of world LIFT-1S UL characteristics: Voltage: 600V (North American standard, higher voltage) Temperature: −25°C to +105°C (extreme range, high-temp optimized) Standards: UL 2562, UL 62, CSA C22.2 No.210.2 Design philosophy: Safety by certification (single core + redundant control) Steel core: 1× core (sufficient with nylon covering) Conductor: Class M (UL, extra fine ~300+ wires per mm²) Cost: Higher (UL testing, certification documentation) Market: North America (USA, Canada), Mexico UL 2562 specialty certification: UL 2562 scope: Elevator and Dumbwaiter Cables Specific requirements: 1. Pendant cable design (cable hangs freely, no duct support) 2. Vertical orientation (designed for gravity-loaded suspension) 3. Repeated flex cycles (cable moves up/down frequently) 4. Safety-critical function (failure = personnel risk) Consequence: More stringent than general-purpose cables Testing includes: Bend cycle fatigue, heat aging, compression resistance Test procedures (unique to UL 2562): Bend cycle test: 1,000+ cycles at minimum bending radius Cable must pass insulation resistance after cycling Heat aging: 500+ hours at 105°C continuous Tensile strength retention minimum 70% Compression: 1,000+ hours under sustained compression Cable cross-section must not exceed 5% permanent deformation LIFT-2S (no UL 2562): Tests per VDE are less stringent on fatigue/cycling Assumes cable mostly static, not repeated flex Adequate for European elevator duty (lower speed, fewer cycles) LIFT-1S UL: All UL 2562 tests passed (proven for North American elevators) Faster cycle times, more frequent motion → more fatigue stress Extra testing ensures reliability under North American elevator duty Market requirement (regulatory): Europe/International: CE mark required (European conformity) VDE/EN/IEC standards sufficient No UL certification needed (not recognized in EU) LIFT-2S is sufficient North America (USA, Canada): UL certification mandatory for elevators UL 2562 specifically for elevator cables CSA dual certification required in Canada LIFT-2S NOT acceptable (lacks UL 2562) LIFT-1S UL mandatory Cost implication: UL certification: ~$5,000–15,000 per product per region Testing duration: 3–6 months per model Documentation: Comprehensive test reports, technical files Result: LIFT-1S UL 20–30% higher cost than equivalent European cable
Technical Department
on10/06/2026

PROTOMONT(Z) NSSHKCGEOEU 0.6/1kV：用于地下采矿自由拖曳作业的钢丝编织增强煤机电缆深度解析

PROTOMONT(Z) NSSHKCGEOEU 0.6/1kV 是一款 coal cutter cables for trailing operations。 它用于 underground machine applications 中的移动设备供电连接，典型设备包括 coal shearer、roadheader、TBM、scoops / LHDs。 与 cable handler 链式运行电缆不同，(Z)-Coal-Cutter cables 专为 free trailing operation 设计，凭借特殊结构可在运行中被拖曳在机器后方相当长的距离
5 Min Read
PROTOMONT(Z) NSSHKCGEOEU 0.6/1KV is a coal cutter cable designed for free trailing operations in underground mining applications, used as power supply connection cable for mobile equipment such as coal shearers, roadheaders, TBMs, or scoops (LHDs). The (Z) Coal-Cutter cables are specifically designed for free trailing operation and, due to their special galvanized steel wire braiding construction, may be trailed for considerable distances behind the machine during operation. Features very finely stranded tinned copper conductors (Class FS), EPR rubber insulation (PROTOLON 3GI3), galvanized steel wire braiding armour, and polychloroprene (PCP) outer sheath (PROTOFIRM 5GM5). Offers up to 36,000N tensile strength and 150m/min travel speed. Certified by MSHA P-189-4, EAC, and Bosnia-Herzegovina BAS.
Technical Department
on14/01/2026

كابل PROTOMONT(Z) NSSHKCGEOEU 0,6/1KVكابلات قاطعات الفحم لعمليات السحب الحر – التعدين تحت الأرض

PROTOMONT(Z) NSSHKCGEOEU 0.6/1KV 是專為地下採礦作業中的自由拖曳操作設計的採煤機電纜，用於連接採煤機、掘進機、隧道掘進機(TBM)或鏟運機(LHD)等移動設備。(Z)型採煤機電纜專為自由拖曳操作設計，由於其特殊的鍍鋅鋼絲編織結構，可在設備後方拖曳相當長的距離。該電纜採用極細絞鍍錫銅導體（FS類）、EPR橡膠絕緣（PROTOLON 3GI3）、鍍鋅鋼絲編織鎧裝、氯丁橡膠外護套（PROTOFIRM 5GM5）。具有高達36,000N的拉伸強度和150m/min的移動速度。獲得MSHA P-189-4、EAC及波黑BAS等國際認證。