[email protected]

не распространяющая горение

4 Min Read
LIFT-2S (European) vs. LIFT-1S UL (North American): LIFT-2S characteristics: Voltage: 300/500V (European standard, lower voltage) Temperature: −40°C to +70°C (moderate range) Standards: VDE 0482 part 265-2-1, EN 50265-2-1, IEC 60332-1-2 Design philosophy: Safety by material redundancy (2 steel cores) Steel cores: 2× cores provide mechanical backup Conductor: Class 6 (European, ~150–200 wires per mm²) Cost: Lower (proven European manufacturing) Market: Europe, Asia-Pacific, most of world LIFT-1S UL characteristics: Voltage: 600V (North American standard, higher voltage) Temperature: −25°C to +105°C (extreme range, high-temp optimized) Standards: UL 2562, UL 62, CSA C22.2 No.210.2 Design philosophy: Safety by certification (single core + redundant control) Steel core: 1× core (sufficient with nylon covering) Conductor: Class M (UL, extra fine ~300+ wires per mm²) Cost: Higher (UL testing, certification documentation) Market: North America (USA, Canada), Mexico UL 2562 specialty certification: UL 2562 scope: Elevator and Dumbwaiter Cables Specific requirements: 1. Pendant cable design (cable hangs freely, no duct support) 2. Vertical orientation (designed for gravity-loaded suspension) 3. Repeated flex cycles (cable moves up/down frequently) 4. Safety-critical function (failure = personnel risk) Consequence: More stringent than general-purpose cables Testing includes: Bend cycle fatigue, heat aging, compression resistance Test procedures (unique to UL 2562): Bend cycle test: 1,000+ cycles at minimum bending radius Cable must pass insulation resistance after cycling Heat aging: 500+ hours at 105°C continuous Tensile strength retention minimum 70% Compression: 1,000+ hours under sustained compression Cable cross-section must not exceed 5% permanent deformation LIFT-2S (no UL 2562): Tests per VDE are less stringent on fatigue/cycling Assumes cable mostly static, not repeated flex Adequate for European elevator duty (lower speed, fewer cycles) LIFT-1S UL: All UL 2562 tests passed (proven for North American elevators) Faster cycle times, more frequent motion → more fatigue stress Extra testing ensures reliability under North American elevator duty Market requirement (regulatory): Europe/International: CE mark required (European conformity) VDE/EN/IEC standards sufficient No UL certification needed (not recognized in EU) LIFT-2S is sufficient North America (USA, Canada): UL certification mandatory for elevators UL 2562 specifically for elevator cables CSA dual certification required in Canada LIFT-2S NOT acceptable (lacks UL 2562) LIFT-1S UL mandatory Cost implication: UL certification: ~$5,000–15,000 per product per region Testing duration: 3–6 months per model Documentation: Comprehensive test reports, technical files Result: LIFT-1S UL 20–30% higher cost than equivalent European cable
Technical Department
on11/06/2026

TDI КВПРэР / КВПРэУ：0.66 kV 变频驱动屏蔽柔性电缆工程解析

HoldFlex TDI КВПРэР 和 HoldFlex TDI КВПРэУ 是额定电压 0.66 kV 的橡胶绝缘屏蔽柔性电缆，执行 ТУ 16.К73.165-2017。该系列用于强功率移动和固定对象、设备、机器、机构以及钻机等场景中的 变频调速电驱动 控制与供电，可用于 0.66 kV、最高 400 Hz 交流系统，也可用于 直流至 1.2 kV 的系统
4 Min Read
BASKET SPREADER 740 (YSLTOE) is engineered specifically for hoisting and control applications where mechanical flexibility and electrical reliability must coexist in marine environments. Unlike load-bearing structural cables (which prioritize tensile strength), control cables emphasize: Conductor flexibility – Repeated bending over pulleys without mechanical fatigue Insulation integrity – Voltage breakdown resistance under salt-fog corrosion Mechanical damping – Rope-like flexibility to drape naturally in spreader bar frames Environmental barrier – Outer sheath blocks salt, moisture, and UV penetration Core Design Elements: Component Material Specification Function Port Environment Benefit Conductor Flexible red copper Class 6 (IEC 60228) Carries 300/500V power; enables bending flexibility High purity copper resists galvanic corrosion Insulation PVC type YI2 (IEC 60811) Electrical isolation; voltage breakdown resistance (2 kV test) PVC with marine additives prevents salt-induced tracking Central Unit Aramide yarns (Kevlar™ equivalent) Mechanical load-bearing backup; structural integrity Aramide resists moisture & salt; absorbs vibration stress Outer Sheath PUR type 11YM1 (DIN 73377) Environmental barrier; UV/ozone/moisture protection Superior salt-fog resistance; 20+ year marine lifespan
Technical Department
on11/06/2026

什么是 КОВГ / КОВГН：6 kV 单芯高压柔性橡胶电缆

КОВГ 和 КОВГН 是额定电压 6 kV、频率 50 Hz 的单芯高压柔性电缆，执行 ТУ 16.К73.004-88。КОВГ 为铜导体、橡胶绝缘、橡胶护套的内部安装柔性电缆；КОВГН 为同类结构，但采用 耐油且不传播燃烧的护套。该系列用于露天和地下矿山作业中的设备、成套产品和机构内部安装
6 Min Read
UNE 22511 — formally titled "Cables flexibles para minería subterránea con tensiones de 1,8/3 kV con aislamiento de caucho, sin armadura" (Flexible cables for underground mining, 1.8/3 kV, rubber-insulated, unarmoured) — is the definitive Spanish standard for heavy-duty power cables connecting underground mobile mining equipment to fixed electrical distribution networks. Published and maintained by AENOR (Asociación Española de Normalización y Certificación), it operates as a specialized overlay on IEC 60502-1, extending that base standard's electrical requirements with the stringent mechanical, safety, and flame-retardancy requirements specific to enclosed underground environments. Despite its Spanish origin, UNE 22511 enjoys a geographic reach far exceeding Iberia. The standard has been adopted — formally or by reference — across the major Spanish-speaking mining economies: Chile, Peru, Colombia, Bolivia, and Mexico, where AENOR-certified cables are accepted by national mining safety regulators as the primary qualification pathway for underground mobile equipment power supply cables. In Chile alone, UNE 22511 cables are installed across dozens of operations including major copper and coal mines. The standard's engineering DNA can be described in a single imperative: extreme dynamic flexibility combined with superior resistance to combined torsional and bending fatigue. This is not merely a performance aspiration — it is a structural requirement that shapes every material choice and geometric decision in the cable's construction. The logic proceeds as follows: Underground mobile equipment (continuous miners, shearers, shuttle cars) moves continuously and repeatedly during operation, dragging its power cable behind it or winding and unwinding it from a cable reel. This motion imposes cyclic bending, axial tension, and torsional loads on the cable simultaneously — a multi-axis fatigue regime of a severity not encountered in any other industrial cable application. Standard fixed-installation cables, even those classified as "flexible," are not designed for this loading regime and will fail in fatigue within weeks to months when installed in drag duty. Therefore, every structural element of a UNE 22511 cable — conductor wire diameter, insulation compound, earth core geometry, armour exclusion, sheath specification — is selected to maximize multi-axis fatigue endurance, not any single performance parameter. ⛏ The Founding Engineering Principle UNE 22511 is an unarmoured drag cable standard. The deliberate absence of any metallic armour — which might superficially seem to reduce robustness — is in fact the defining engineering choice that makes the standard viable. Steel wire or tape armour in a continuously torsionally-loaded cable acts as a progressive-failure torsional spring: each twist cycle accumulates irreversible plastic strain in the armour wires, leading to wire fractures within 10,000–30,000 cycles. For a shuttle car cable experiencing 80,000+ torsional cycles per year, armour represents not additional protection but a built-in scheduled failure mechanism. The UNE 22511 design eliminates this failure mode at source.
Technical Department
on11/06/2026

什么是 HoldMine КГпЭ 系列：6 kV 挖掘机与矿山移动设备柔性屏蔽动力电缆

HoldMine КГпЭ、КГпЭТ、КГпЭц、КГпЭНШ、КГпЭТБШ、КГпЭ1、КГпЭ2、КГпЭ-ХЛ、КГпЭ1-ХЛ、КГпЭц-ХЛ、КГпЭц-с 是一组额定电压 6 kV 的柔性屏蔽动力电缆，执行 ТУ 16.К73.064-2002，并符合 ГОСТ 31945-2012 要求。该系列用于挖掘机、其他移动机构或电气装置，在露天矿山、地下矿山、挖泥船和其他水上设施中连接到 中性点绝缘的 50 Hz 交流电网；主线芯额定电压为 6 kV，辅助线芯额定电压为 0.38 kV。
5 Min Read
Advanced High-Flexibility Salt-Fog Resistant Port Cable: Engineering Excellence for Extreme Maritime Environments A comprehensive technical deep-dive into Feichun's purpose-engineered high-flexibility port cable platform combining advanced electrochemical conductor protection, specialized EPR insulation, proprietary hydrophobic semi-conductive interfaces, and innovative outer-sheath chemistry—delivering extended service-life durability (12–15+ years field-validated) for demanding dredging, pumping, and floating-crane applications operating in harsh tropical and subtropical saltwater port facilities worldwide.
Technical Department
on11/06/2026

什么是 КПГ, КПГН, КПГСН, КПГУ：0.38/0.66 kV 柔性动力电缆

КГЭТЭШм 是一种用于地下采矿移动机器和机构的 柔性屏蔽动力电缆，适用于带 частотным регулированием 的电气网络，也就是带变频调速控制的矿山供电系统。该型号额定交流电压为 3.3 kV 和 6 kV，执行 ТУ 16.К73.059-2021，火灾危险等级按 ГОСТ 31565-2012 为 О1.8.2.5.4，产品分类代码为 ОКПД2 27.32.13.129。它的结构核心不是普通橡套电缆的单层防护，而是 主线芯屏蔽、分裂接地线、铜丝总屏蔽、耐热橡胶绝缘和高耐磨抗撕裂护套 共同组成的中压变频矿山移动供电系统
5 Min Read
FLEXIFESTOON® NE-FLAT (NGFLGÖU): Advanced High-Flexibility Anti-Salt Fog Port Cable for Maritime Cargo Handling and Marine Automation Systems Feichun's revolutionary FLEXIFESTOON® NE-FLAT NGFLGÖU flat cable combines extreme high-flexibility architecture with marine-grade anti-salt fog protection, engineered specifically for port automation infrastructure, cargo-handling festoon systems, and maritime equipment control requiring superior corrosion resistance and mechanical reliability through thousands of bending cycles in aggressive saltwater environments.
Technical Department
on11/06/2026

什么是 GOST КГЭЖ ：井下自走车辆用柔性屏蔽动力电缆

КГЭЖ 与 HoldMine КГЭпЖ 是用于地下采矿自走车辆的柔性屏蔽动力电缆，资料将其定义为 Кабели силовые гибкие экранированные для самоходных вагонов。它们服务的不是普通地面移动设备，而是 подземные горные работы 井下采矿作业中带电驱动的 самоходные вагоны 自走车辆。电缆主线芯用于 1140 V、50 Hz 交流动力供电，辅助线芯用于 220 V 辅助回路。其结构采用第 5 类多股铜导体、橡胶绝缘、导电橡胶屏蔽、合成线增强束、成型增强芯和耐油阻燃橡胶护套，核心目标是在狭窄、潮湿、磨损、弯折频繁的井下移动环境中，提供动力供电、辅助控制和屏蔽安全的统一电缆方案
4 Min Read
H07RN-F: Advanced High-Flexibility Salt-Fog Resistant Port Cable Engineering Solution Specialized rubber-sheathed electrical cable engineered for extreme maritime and coastal port environments. H07RN-F combines superior mechanical flexibility (4×D minimum fixed-laying bending radius, 6×D flexible-application capability) with comprehensive salt-fog environmental resistance, enabling reliable 450/750V power distribution and control signaling in container gantry systems, ship loaders, and port automation infrastructure where conventional cables fail within 6–12 months of deployment.
Technical Department
on11/06/2026

什么是 GOST/EAC КГЭС：自走式矿车用柔性屏蔽动力电缆

КГЭС 是一种用于 самоходные вагоны 自走式矿车的柔性屏蔽动力电缆，俄文资料定义为“Кабель силовой гибкий экранированный для самоходных вагонов”。它用于将带电驱动的自走式矿车连接到 50 Hz 交流电网，主线芯额定电压为 1140 V，辅助线芯额定电压为 220 V。该电缆采用第 5 类柔性铜导体、橡胶绝缘、导电橡胶个别屏蔽、合成线加强绞束和耐油不延燃橡胶护套，适合矿用移动车辆的弯曲、折弯、油污和单根敷设安全要求
5 Min Read
LIFT-2S (European) vs. LIFT-1S UL (North American): LIFT-2S characteristics: Voltage: 300/500V (European standard, lower voltage) Temperature: −40°C to +70°C (moderate range) Standards: VDE 0482 part 265-2-1, EN 50265-2-1, IEC 60332-1-2 Design philosophy: Safety by material redundancy (2 steel cores) Steel cores: 2× cores provide mechanical backup Conductor: Class 6 (European, ~150–200 wires per mm²) Cost: Lower (proven European manufacturing) Market: Europe, Asia-Pacific, most of world LIFT-1S UL characteristics: Voltage: 600V (North American standard, higher voltage) Temperature: −25°C to +105°C (extreme range, high-temp optimized) Standards: UL 2562, UL 62, CSA C22.2 No.210.2 Design philosophy: Safety by certification (single core + redundant control) Steel core: 1× core (sufficient with nylon covering) Conductor: Class M (UL, extra fine ~300+ wires per mm²) Cost: Higher (UL testing, certification documentation) Market: North America (USA, Canada), Mexico UL 2562 specialty certification: UL 2562 scope: Elevator and Dumbwaiter Cables Specific requirements: 1. Pendant cable design (cable hangs freely, no duct support) 2. Vertical orientation (designed for gravity-loaded suspension) 3. Repeated flex cycles (cable moves up/down frequently) 4. Safety-critical function (failure = personnel risk) Consequence: More stringent than general-purpose cables Testing includes: Bend cycle fatigue, heat aging, compression resistance Test procedures (unique to UL 2562): Bend cycle test: 1,000+ cycles at minimum bending radius Cable must pass insulation resistance after cycling Heat aging: 500+ hours at 105°C continuous Tensile strength retention minimum 70% Compression: 1,000+ hours under sustained compression Cable cross-section must not exceed 5% permanent deformation LIFT-2S (no UL 2562): Tests per VDE are less stringent on fatigue/cycling Assumes cable mostly static, not repeated flex Adequate for European elevator duty (lower speed, fewer cycles) LIFT-1S UL: All UL 2562 tests passed (proven for North American elevators) Faster cycle times, more frequent motion → more fatigue stress Extra testing ensures reliability under North American elevator duty Market requirement (regulatory): Europe/International: CE mark required (European conformity) VDE/EN/IEC standards sufficient No UL certification needed (not recognized in EU) LIFT-2S is sufficient North America (USA, Canada): UL certification mandatory for elevators UL 2562 specifically for elevator cables CSA dual certification required in Canada LIFT-2S NOT acceptable (lacks UL 2562) LIFT-1S UL mandatory Cost implication: UL certification: ~$5,000–15,000 per product per region Testing duration: 3–6 months per model Documentation: Comprehensive test reports, technical files Result: LIFT-1S UL 20–30% higher cost than equivalent European cable
Technical Department
on11/06/2026

什么是 КРЭВБбШ、КРЭВКШв、КРЭВКбШ、КВЭмВБбШ、КВЭмВКШ、КВЭмВКбШ、КПвЭмВБбШ、КПвЭмВКШ、КПвЭмВКбШ、КРЭВБбШв 高电气安全铠装矿山动力电缆：0.66、1.2 和 6 kV 屏蔽铠装供电系统工程解析

armoured mining power cable 6 kV 6 kV 铠装屏蔽矿山动力电缆 用于矿山中压馈电、变电站到设备区供电。 enhanced electrical safety mining cable повышенной электробезопасности 强调接地、屏蔽、铠装和故障安全。 screened armoured cable with PE and auxiliary core 3×S + 接地线芯 + 辅助线芯 + 铜丝屏蔽 同时服务动力、保护接地和辅助监测/控制。 water blocked mining cable г、2г、гж、2гж 密封结构 护套破损后限制水分沿电缆纵向传播。 low fire hazard mining cable PVC 低火灾危险、无卤聚合物、阻燃橡胶、无卤 TPU 适合矿山巷道、地下空间和人员安全要求更高的区域。 cold resistant armoured cable нг(А)-ХЛ 可至 -60°C 寒冷地区露天矿山、井口、地面变电站到井下入口。 7.5D bending radius cable 最小敷设弯曲半径 ≥ 7.5Dн 指导托架、转弯、井下敷设和牵引路径设计。