VFD Motor Bearings: Why do Siemens variable frequency drives require (N)3GHSSYCY 3×150+3×25 to prevent bearing pitting? \u2014 Feichun Cable<\/title>\n<meta name=\"description\" content=\"Complete technical guide explaining why bearing pitting is the leading failure mode in variable frequency drive (VFD) motor systems and how symmetric (N)3GHSSYCY cables with 3+3 earth conductor configuration prevent this catastrophic damage. Teaches the fundamental physics of how PWM switching creates high-frequency common mode voltage that induces shaft voltages in motor rotors, leading to electrical discharge machining (EDM) erosion of bearing surfaces. Explains how conventional 3-phase plus ground cable geometries fail to cancel asymmetric high-frequency magnetic fields, allowing zero-sequence currents to flow through motor bearings. Details how the symmetric 3+3 conductor arrangement provides perfect geometric balance for high-frequency field cancellation while dual shielding (aluminum foil plus tinned copper braid) provides low-impedance return paths. Emphasizes the absolute requirement for dual 360-degree grounding at both motor and VFD ends using proper EMC cable glands, explaining why single-end grounding creates giant radiation antennae that propagate EMI rather than controlling it. Provides detailed technical specifications for (N)3GHSSYCY including mutual capacitance reduction compared to conventional cables, stranding geometry optimized for high-frequency performance, and ampacity calculations for inverter duty cycles. Addresses critical field installation errors including improper cable termination, inadequate shielding connections, insufficient filtering for long cable runs, and cable routing that compromises symmetry. The document establishes that proper VFD cabling is not optional equipment upgrade but essential engineering solution for motor longevity and system reliability, backed by electromagnetic theory and decades of industrial drive experience.\">\n<style>\n\/* ===== RESET & VARIABLES ===== *\/\n*,*::before,*::after{box-sizing:border-box;margin:0;padding:0}\n:root{\n--bg:#fff;--bg2:#f5f6f8;--bg3:#ebedf0;--tx:#16192b;--tx2:#4b5068;--tx3:#6e7489;\n--ac:#0059b3;--ac2:#003f7f;--acL:#dbeafe;--bd:#d2d6dc;\n--thBg:#0b1426;--thTx:#dde4ef;--trAlt:#f0f3f7;--hover:#eef2ff;\n--cardBg:#fff;--cardBd:#e3e7ed;--codeBg:#f1f4f9;--keyBg:#edf2ff;--keyBd:#0059b3;\n--shadow:0 1px 3px rgba(0,0,0,.07);--cn:#707890;\n--tagBg:#e6f0fd;--tagTx:#1a52c9;--gn:#15803d;--rd:#dc2626;--am:#d97706;\n--dangerBg:#fef2f2;--dangerBd:#f87171;--successBg:#f0fdf4;--successBd:#4ade80;\n--warnBg:#fffbeb;--warnBd:#fbbf24;\n}\n@media(prefers-color-scheme:dark){:root{\n--bg:#0e1018;--bg2:#181b2b;--bg3:#222640;--tx:#e0e5f0;--tx2:#9da5bf;--tx3:#6d7590;\n--ac:#6baafc;--ac2:#9cc5ff;--acL:#172b4d;--bd:#2b3050;\n--thBg:#0d1220;--thTx:#c8d0e0;--trAlt:#1c2038;--hover:#1d2a48;\n--cardBg:#181b2b;--cardBd:#2b3050;--codeBg:#1a2236;--keyBg:#152240;--keyBd:#5a9cf5;\n--shadow:0 1px 4px rgba(0,0,0,.3);--cn:#6d7590;\n--tagBg:#1a3560;--tagTx:#9cc5ff;--gn:#4ade80;--rd:#f87171;--am:#fbbf24;\n--dangerBg:#2a1215;--dangerBd:#ef4444;--successBg:#0f2a18;--successBd:#22c55e;\n--warnBg:#2a2210;--warnBd:#eab308;\n}}\n\/* ===== BASE ===== *\/\nhtml{font-size:16px;scroll-behavior:smooth}\nbody{font-family:-apple-system,BlinkMacSystemFont,'Segoe UI',Roboto,'Helvetica Neue',Arial,sans-serif;background:var(--bg);color:var(--tx);line-height:1.78}\na{color:var(--ac);text-decoration:none}a:hover{text-decoration:underline}\n.w{max-width:980px;margin:0 auto;padding:28px 22px 60px}\n.cn{color:var(--cn);font-size:.86em;font-style:italic}\n\n\/* ===== HEADER ===== *\/\n.hero{text-align:center;padding:44px 0 30px;border-bottom:2px solid var(--bd);margin-bottom:34px}\n.hero .co{font-size:.82rem;color:var(--ac);font-weight:700;letter-spacing:1.8px;text-transform:uppercase;margin-bottom:8px}\n.hero h1{font-size:1.7rem;font-weight:800;line-height:1.32;margin-bottom:12px}\n.hero .sub{font-size:.94rem;color:var(--tx2);max-width:700px;margin:0 auto}\n.meta{display:flex;flex-wrap:wrap;gap:10px 26px;font-size:.8rem;color:var(--tx3);padding-bottom:18px;border-bottom:1px solid var(--bd);margin-bottom:30px}\n\n\/* ===== TOC ===== *\/\n.toc{background:var(--bg2);border:1px solid var(--bd);border-radius:6px;padding:18px 22px;margin-bottom:32px}\n.toc h3{font-size:.85rem;text-transform:uppercase;letter-spacing:1px;color:var(--tx3);margin:0 0 10px;font-weight:700}\n.toc ol{padding-left:20px;font-size:.87rem;line-height:2.1}\n.toc a{color:var(--ac)}\n\n\/* ===== ARTICLE ===== *\/\narticle h2{font-size:1.32rem;font-weight:700;margin:38px 0 14px;padding-bottom:7px;border-bottom:2px solid var(--ac);display:inline-block}\narticle h3{font-size:1.08rem;font-weight:600;margin:22px 0 10px;color:var(--tx)}\narticle p{margin-bottom:15px;color:var(--tx2)}\narticle p.lead{font-size:1.01rem;color:var(--tx);font-weight:400}\n\n\/* ===== CALLOUT BOXES ===== *\/\n.box{padding:14px 18px;margin:18px 0;border-radius:0 6px 6px 0;border-left:4px solid}\n.box p{margin:0;font-size:.91rem}\n.box-key{background:var(--keyBg);border-color:var(--keyBd)}\n.box-danger{background:var(--dangerBg);border-color:var(--dangerBd)}\n.box-success{background:var(--successBg);border-color:var(--successBd)}\n.box-warn{background:var(--warnBg);border-color:var(--warnBd)}\n\n\/* ===== TABLES ===== *\/\n.tw{overflow-x:auto;margin:18px 0 26px;border:1px solid var(--bd);border-radius:6px}\ntable{width:100%;border-collapse:collapse;font-size:.86rem}\ntable caption{text-align:left;font-weight:700;font-size:.94rem;padding:11px 15px;background:var(--bg2);border-bottom:1px solid var(--bd)}\nthead{background:var(--thBg)}\nthead th{color:var(--thTx);font-weight:600;text-align:left;padding:9px 13px;white-space:nowrap;font-size:.8rem;text-transform:uppercase;letter-spacing:.5px}\ntbody td{padding:8px 13px;border-bottom:1px solid var(--bd);vertical-align:top}\ntbody tr:nth-child(even){background:var(--trAlt)}\ntbody tr:hover{background:var(--hover)}\ntd code,p code{background:var(--codeBg);padding:1px 5px;border-radius:3px;font-size:.85em;font-family:'SF Mono',Consolas,monospace}\n.vg{color:var(--gn);font-weight:600}.vr{color:var(--rd);font-weight:600}.va{color:var(--am);font-weight:600}\n\n\/* ===== STAT ROW ===== *\/\n.stats{display:grid;grid-template-columns:repeat(auto-fit,minmax(200px,1fr));gap:14px;margin:22px 0 28px}\n.stat{background:var(--bg2);border:1px solid var(--bd);border-radius:6px;padding:16px;text-align:center}\n.stat .num{font-size:1.6rem;font-weight:800;color:var(--ac);line-height:1.2}\n.stat .lbl{font-size:.78rem;color:var(--tx3);margin-top:4px;line-height:1.3}\n\n\/* ===== SOURCES ===== *\/\n.sources{margin-top:40px;padding-top:24px;border-top:2px solid var(--bd)}\n.sources ol{padding-left:22px;font-size:.82rem;color:var(--tx3);line-height:2}\n.sources a{color:var(--ac);word-break:break-all}\n\n\/* ===== CONTACT ===== *\/\n.contact{background:var(--bg2);border:1px solid var(--bd);border-radius:8px;padding:24px;margin-top:36px}\n.contact h2{border-bottom:none;margin-top:0;padding-bottom:0}\n.cg{display:grid;grid-template-columns:repeat(auto-fit,minmax(210px,1fr));gap:14px;margin-top:14px}\n.cc{background:var(--cardBg);border:1px solid var(--cardBd);border-radius:6px;padding:13px 15px}\n.cc .lb{font-size:.76rem;text-transform:uppercase;color:var(--tx3);letter-spacing:.5px;margin-bottom:3px;font-weight:600}\n.cc .vl{font-size:.9rem;color:var(--tx)}\n.cc a{color:var(--ac)}\n\nfooter{text-align:center;padding:28px 0 0;margin-top:38px;border-top:1px solid var(--bd);font-size:.78rem;color:var(--tx3)}\n@media(max-width:640px){\n .hero h1{font-size:1.3rem}.w{padding:16px 14px 40px}\n thead th,tbody td{padding:7px 8px;font-size:.79rem}\n .stats{grid-template-columns:1fr 1fr}\n}\n<\/style>\n<\/head>\n<body>\n<div class=\"w\">\n\n<header class=\"hero\">\n<div class=\"co\">Feichun Cable Technical Division <span class=\"cn\">\u98de\u7eaf\u7535\u7f06\u6280\u672f\u90e8<\/span><\/div>\n<h1>VFD Motor Bearings: Why do Siemens variable frequency drives require (N)3GHSSYCY 3×150+3×25 to prevent bearing pitting? Understanding the physics of shaft voltage and EMC. <span class=\"cn\">\u53d8\u9891\u7535\u673a\u8f74\u627f\uff1a\u4e3a\u4ec0\u4e48\u897f\u95e8\u5b50\u53d8\u9891\u5668\u9700\u8981 (N)3GHSSYCY \u6765\u9632\u6b62\u8f74\u627f\u70b9\u8680\uff1f\u7406\u89e3\u8f74\u7535\u538b\u548c EMC \u7684\u7269\u7406\u539f\u7406<\/span><\/h1>\n<p class=\"sub\">A comprehensive technical guide explaining why bearing pitting has become the leading premature failure mode in variable frequency drive (VFD) motor systems, and how proper cable design with symmetric conductor geometry prevents this catastrophic damage. This document teaches the fundamental physics underlying bearing pitting\u2014beginning with how PWM switching in modern IGBT-based variable frequency drives creates microsecond-scale voltage changes (dv\/dt) that induce common-mode voltages, progressing through the mechanism by which asymmetric cable geometries allow zero-sequence currents to flow through motor bearings, and concluding with how the symmetric (N)3GHSSYCY cable design with dual shielding and proper grounding prevents these currents and protects bearing surfaces. Rather than treating bearing pitting as mysterious equipment failure, this guide explains the electromagnetic mechanisms that cause it, the role of capacitive coupling in creating shaft voltage, and how electrical discharge machining (EDM) gradually erodes bearing surfaces. The document teaches why conventional three-phase-plus-ground cables with asymmetric geometry fail to cancel high-frequency magnetic fields, allowing asymmetric capacitive currents to flow through the motor rotor and bearings. It explains how the (N)3GHSSYCY cable design with perfectly symmetric 3+3 earth conductor configuration provides geometric balance that cancels asymmetric fields, while dual shielding (aluminum foil plus tinned copper braid) creates low-impedance return paths for high-frequency common-mode currents. The document emphasizes the absolute critical requirement for dual 360-degree shielding grounding at both the variable frequency drive and motor ends using proper EMC cable glands, explaining why single-end grounding creates a giant radiation antenna that propagates electromagnetic interference rather than controlling it. Provides detailed technical specifications, ampacity calculations for inverter duty cycles, and practical commissioning procedures. Addresses the most common field installation errors that negate the cable’s protective benefits and lead to continued bearing damage despite cable selection.<\/p>\n<\/header>\n\n<div class=\"meta\">\n<span>Published: 2026<\/span>\n<span>Category: Industrial Motor Drive Systems <span class=\"cn\">\u5de5\u4e1a\u7535\u673a\u9a71\u52a8\u7cfb\u7edf<\/span><\/span>\n<span>Reading time: ~33 min<\/span>\n<\/div>\n\n\n<nav class=\"toc\">\n<h3>Table of Contents <span class=\"cn\">\u76ee\u5f55<\/span><\/h3>\n<ol>\n<li><a href=\"#s1\">The Bearing Pitting Crisis: Why Motors Fail Prematurely with VFD Systems<\/a><\/li>\n<li><a href=\"#s2\">Understanding PWM Switching and the Creation of Common-Mode Voltage<\/a><\/li>\n<li><a href=\"#s3\">From Common-Mode Voltage to Shaft Voltage: The Capacitive Coupling Path<\/a><\/li>\n<li><a href=\"#s4\">The EDM Mechanism: How Electrical Discharge Machining Erodes Bearing Surfaces<\/a><\/li>\n<li><a href=\"#s5\">Why Conventional Cables Fail: Asymmetric Geometry and Zero-Sequence Currents<\/a><\/li>\n<li><a href=\"#s6\">The (N)3GHSSYCY Solution: Symmetric 3+3 Earth Conductor Design<\/a><\/li>\n<li><a href=\"#s7\">Dual Shielding: Aluminum Foil and Tinned Copper Braid Working Together<\/a><\/li>\n<li><a href=\"#s8\">The Absolute Requirement for Dual 360-Degree Shielding Grounding<\/a><\/li>\n<li><a href=\"#s9\">Capacitive Coupling Reduction Through Low-Mutual-Capacitance Design<\/a><\/li>\n<li><a href=\"#s10\">Continuous Ampacity for (N)3GHSSYCY in Inverter Duty Service<\/a><\/li>\n<li><a href=\"#s11\">Long Cable Runs and Voltage Reflection: When Filtering Becomes Mandatory<\/a><\/li>\n<li><a href=\"#s12\">Critical Installation Errors That Negate Cable Protective Benefits<\/a><\/li>\n<li><a href=\"#s13\">Field Commissioning and Verification Procedures<\/a><\/li>\n<li><a href=\"#s14\">References & Standards<\/a><\/li>\n<\/ol>\n<\/nav>\n\n<article>\n\n<h2 id=\"s1\">1. The Bearing Pitting Crisis: Why Motors Fail Prematurely with VFD Systems <span class=\"cn\">\u8f74\u627f\u70b9\u8680\u5371\u673a\uff1a\u4e3a\u4ec0\u4e48\u7535\u673a\u5728\u53d8\u9891\u7cfb\u7edf\u4e2d\u8fc7\u65e9\u5931\u6548<\/span><\/h2>\n\n<p class=\"lead\">In the industrial drive systems community, a troubling pattern has emerged over the past 15\u201320 years: motors operating with variable frequency drives (VFDs) are failing prematurely at rates far exceeding what was experienced with motors running on direct line power. The most common failure mode is not overheating, not insulation breakdown, but rather <strong>bearing pitting\u2014a surface degradation of the rolling elements and races in motor bearings that develops progressively until the bearing becomes non-functional<\/strong>. Engineers initially thought this was merely a cable size issue or a thermal management problem. More careful investigation revealed the true cause: electromagnetic phenomena unique to high-frequency PWM switching were creating conditions that slowly eroded bearing surfaces through electrical discharge machining (EDM). The solution required not larger cables or better cooling, but specifically engineered cables with symmetric conductor geometry and dual shielding designed to control the electromagnetic environment inside the motor. Understanding this problem and its solution requires learning about electromagnetic phenomena that many motor engineers were never formally taught\u2014the behavior of common-mode voltage, shaft voltage, and capacitive coupling in high-frequency environments. This is not obscure physics for academics; it is practical engineering knowledge that determines whether motors survive their design life or fail prematurely after 2\u20133 years of operation.<\/p>\n\n<p>The bearing pitting problem became severe enough that IEEE issued Task Force recommendations, manufacturers developed specialized bearing designs, and cable suppliers engineered dedicated VFD cables. Yet many practitioners still do not fully understand why proper cable design is essential rather than optional. This document teaches the physical principles underlying bearing pitting, explains how it occurs step by step, and demonstrates how the (N)3GHSSYCY cable architecture directly addresses and prevents each mechanism that leads to damage. Rather than simply asserting that you must use symmetric cables with dual shielding, this guide explains the electromagnetic physics that makes this design essential. Understanding these principles will help you make intelligent decisions about when (N)3GHSSYCY cables are mandatory, how to commission them properly, and how to troubleshoot problems when they arise.<\/p>\n\n<div class=\"stats\">\n<div class=\"stat\"><div class=\"num\">dv\/dt<\/div><div class=\"lbl\">Voltage change rate from PWM switching <span class=\"cn\">PWM \u5f00\u5173\u4ea7\u751f\u7684\u7535\u538b\u53d8\u5316\u7387<\/span><\/div><\/div>\n<div class=\"stat\"><div class=\"num\">MHz<\/div><div class=\"lbl\">Frequency range of common-mode noise <span class=\"cn\">\u5171\u6a21\u566a\u58f0\u9891\u7387\u8303\u56f4<\/span><\/div><\/div>\n<div class=\"stat\"><div class=\"num\">EDM<\/div><div class=\"lbl\">Erosion mechanism: Electrical Discharge Machining <span class=\"cn\">\u4fb5\u8680\u673a\u5236\uff1a\u7535\u706b\u82b1\u52a0\u5de5<\/span><\/div><\/div>\n<div class=\"stat\"><div class=\"num\">3+3<\/div><div class=\"lbl\">Symmetric earth conductor configuration <span class=\"cn\">\u5bf9\u79f0\u63a5\u5730\u5bfc\u4f53\u7ed3\u6784<\/span><\/div><\/div>\n<\/div>\n\n<div class=\"box box-danger\">\n<p><strong>The Bearing Pitting Reality \u26a0\ufe0f \u8f74\u627f\u70b9\u8680\u73b0\u5b9e\uff1a<\/strong> Bearing pitting in VFD motors is not rare or exceptional\u2014it is the rule rather than the exception for systems without proper EMC cable selection. Motors have been removed from service after 18 months of operation with bearing damage that required complete bearing replacement. The damage is visible under magnification as microscopic craters covering the bearing race surfaces. This is not a slow wear process that can be tolerated until scheduled maintenance\u2014once pitting becomes established, the bearing’s structural integrity is compromised and failure can be catastrophic. Implementing proper EMC cable design and grounding is not an optional upgrade or a “nice-to-have” specification. It is the engineering solution that determines whether motors operate for their full 20+ year design life or fail prematurely within 2\u20133 years. This is not overstating the issue.<\/p>\n<\/div>\n\n\n<h2 id=\"s2\">2. Understanding PWM Switching and the Creation of Common-Mode Voltage <span class=\"cn\">\u7406\u89e3 PWM \u5f00\u5173\u548c\u5171\u6a21\u7535\u538b\u7684\u4ea7\u751f<\/span><\/h2>\n\n<p>To understand why bearing pitting occurs in VFD systems, you must first understand how modern variable frequency drives create the electromagnetic environment that leads to bearing damage. This begins with understanding PWM (pulse-width modulation) switching and the resulting voltage characteristics.<\/p>\n\n<p>A variable frequency drive converts three-phase AC power into DC power (through a rectifier), then converts that DC power back into three-phase AC power at a different frequency and voltage using IGBT (insulated-gate bipolar transistor) switches. The IGBT switches operate at very high frequency\u2014typically 4\u201316 kHz in industrial drives, sometimes higher in specialized applications. These switches turn on and off thousands of times per second, creating a PWM waveform that approximates the desired sinusoidal output voltage. From the motor’s perspective, it receives a waveform that looks like a staircase approximation of a sine wave rather than a smooth sinusoid.<\/p>\n\n<p>The critical characteristic of this switching is the rate of voltage change, expressed as dv\/dt. When an IGBT switch turns on or off, the voltage changes in microseconds (millionths of a second). This creates extremely high rates of voltage change\u2014perhaps 10,000 volts per microsecond or higher. This is millions of times faster than the voltage change rate in a 60 Hz AC sine wave. This extremely rapid voltage change propagates along the cable and couples into the motor windings.<\/p>\n\n<p>Now here is where the problem begins: the three-phase PWM pulses from the drive do not have exactly equal timing. Due to inevitable small differences in the switching time of the three IGBT pairs, there is a small time skew where the three phases do not switch at exactly the same instant. This timing skew creates a common-mode voltage\u2014a voltage that appears between all three phase conductors and ground (or the cable shield). The common-mode voltage is typically much smaller in magnitude than the phase-to-phase voltage, perhaps 10\u201330% of the DC bus voltage. But because of the extremely high dv\/dt, this common-mode voltage contains very high frequency components in the megahertz range. These megahertz-frequency components are the source of the problem.<\/p>\n\n<\/article>\n\n<article>\n\n<h2 id=\"s3\">3. From Common-Mode Voltage to Shaft Voltage: The Capacitive Coupling Path <span class=\"cn\">\u4ece\u5171\u6a21\u7535\u538b\u5230\u8f74\u7535\u538b\uff1a\u5bb9\u6027\u8026\u5408\u8def\u5f84<\/span><\/h2>\n\n<p>Now that you understand how PWM switching creates common-mode voltage, we need to trace the path by which this voltage appears on the motor rotor and creates damaging currents through the bearings. This requires understanding capacitive coupling\u2014how voltage can be transmitted from one conductor to another through the electric field between them.<\/p>\n\n<p>Between the motor stator windings and the motor rotor, there is inherent capacitance\u2014not by design, but simply as a result of the motor’s physical structure. The stator creates a strong electric field when high-frequency voltage is applied to the windings. The rotor sits inside this field and becomes capacitively coupled to it. When the common-mode voltage (which includes high-frequency components) appears on the stator, the capacitive coupling transfers some of this voltage to the rotor, creating what is called shaft voltage.<\/p>\n\n<p>The magnitude of shaft voltage depends on several factors: the amplitude of the common-mode voltage, the frequency content (higher frequencies couple more easily), and the capacitance between stator and rotor. In modern motors with PWM drive systems, shaft voltages in the range of 100\u2013400 volts can develop. This seems problematic\u2014a 200-volt difference between the rotor and the bearing race could cause electrical breakdown.<\/p>\n\n<p>But here is the critical insight: if the capacitive coupling path is symmetric\u2014meaning the high-frequency fields couple equally to the rotor from all three phases\u2014then the common-mode current that flows from the rotor to ground through the bearings is distributed evenly. The rotor sits at a relatively uniform potential, the current path is well-defined, and the bearing damage, while still possible, is minimized or prevented by proper grounding design.<\/p>\n\n<p>However, if the cable geometry is asymmetric\u2014meaning the three phases are not equally positioned relative to ground\u2014then the capacitive coupling is asymmetric. One phase couples more strongly to the rotor than the others, creating an imbalance. This asymmetry drives asymmetric currents through the rotor and bearings, creating the conditions for the EDM (electrical discharge machining) that erodes bearing surfaces. This is where conventional cables become problematic and where symmetric (N)3GHSSYCY cables become essential.<\/p>\n\n<\/article>\n\n<article>\n\n<h2 id=\"s4\">4. The EDM Mechanism: How Electrical Discharge Machining Erodes Bearing Surfaces <span class=\"cn\">EDM \u673a\u5236\uff1a\u7535\u706b\u82b1\u52a0\u5de5\u5982\u4f55\u4fb5\u8680\u8f74\u627f\u8868\u9762<\/span><\/h2>\n\n<p>To understand why bearing pitting develops and becomes irreversible, we need to examine the specific mechanism by which the rotor-to-bearing current erodes metal surfaces. This mechanism is electrical discharge machining\u2014the same physical process used in industrial EDM machines to cut hard materials with electrical sparks.<\/p>\n\n<p>When shaft voltage creates a potential difference between the rotor and the bearing race, and when asymmetric currents flow through the bearings, localized high-current-density paths develop between the rotor and the bearing. These localized current concentrations create tiny electrical arcs (arcing) at the contact points. The temperature of these arcs is extremely high\u2014thousands of degrees. In a fraction of a microsecond, these high-temperature arcs melt and vaporize a tiny volume of the bearing surface metal. When the arc extinguishes, the molten metal resolidifies in a different crystalline structure, creating a small pit. On the next PWM cycle, another arc forms, creating another pit at a slightly different location. After thousands or millions of PWM cycles, the bearing race surface becomes covered with microscopic pits\u2014the characteristic “pitting” pattern seen in failed bearings.<\/p>\n\n<p>The critical aspect of this mechanism is that it is progressive and irreversible. The pitted surface changes the bearing’s geometry and increases vibration, which further concentrates stress and accelerates the pitting process. Once pitting becomes established, it accelerates until the bearing completely fails. This explains why bearing pitting leads to catastrophic failure rather than slow degradation: it is a self-reinforcing failure mode.<\/p>\n\n<p>The key to preventing bearing pitting is preventing the asymmetric currents that create the localized high-density current paths where arcing occurs. Symmetric cable design achieves this by ensuring that the high-frequency fields coupling to the rotor are balanced, preventing asymmetric current concentration and the arcing that causes pitting.<\/p>\n\n<\/article>\n\n<article>\n\n<h2 id=\"s5\">5. Why Conventional Cables Fail: Asymmetric Geometry and Zero-Sequence Currents <span class=\"cn\">\u4e3a\u4ec0\u4e48\u5e38\u89c4\u7535\u7f06\u5931\u8d25\uff1a\u4e0d\u5bf9\u79f0\u51e0\u4f55\u548c\u96f6\u5e8f\u7535\u6d41<\/span><\/h2>\n\n<p>Now we can explain why conventional three-phase plus ground cables are inadequate for VFD service and why they allow the bearing pitting mechanism to develop. This requires understanding how cable geometry determines the electromagnetic field distribution and the resulting capacitive coupling.<\/p>\n\n<p>A conventional VFD cable typically has three phase conductors and one ground conductor. The simplest arrangement places the three phases in a triangular pattern and the ground conductor at one side. This creates an asymmetric geometry where the three phase conductors are not equally positioned relative to the ground reference. When PWM common-mode voltage appears on the three phases, the asymmetric cable geometry means the voltage couples differently to each phase. One phase is closer to the ground shield, another is farther, and the third is at some intermediate distance. This asymmetry means that the high-frequency electric field is not balanced\u2014the field is stronger in some directions than others.<\/p>\n\n<p>This asymmetric field couples asymmetrically to the motor rotor through the distributed capacitance. The rotor does not sit at a uniform potential relative to ground. Instead, it experiences higher potential difference from one phase than from the others. This potential imbalance drives zero-sequence currents\u2014currents that flow from the rotor through the bearings to ground, taking the path of least impedance through the bearing lubricant and ball\/race contacts.<\/p>\n\n<p>These zero-sequence currents flowing through the bearings are the source of the arcing and EDM damage. With conventional asymmetric cables, there is no symmetry to balance the currents and prevent concentration. The currents flow wherever the asymmetry drives them, creating hot spots where arcing occurs and bearing pitting initiates.<\/p>\n\n<\/article>\n\n<article>\n\n<h2 id=\"s6\">6. The (N)3GHSSYCY Solution: Symmetric 3+3 Earth Conductor Design <span class=\"cn\">(N)3GHSSYCY \u89e3\u51b3\u65b9\u6848\uff1a\u5bf9\u79f0 3+3 \u63a5\u5730\u5bfc\u4f53\u8bbe\u8ba1<\/span><\/h2>\n\n<p>The engineering solution to prevent bearing pitting requires eliminating the asymmetry that creates zero-sequence currents. The (N)3GHSSYCY cable accomplishes this through a fundamental redesign of the conductor geometry: instead of three phase conductors and one ground conductor, it uses three phase conductors and three distributed earth conductors arranged in a perfectly symmetric pattern.<\/p>\n\n<p>Imagine the cable cross-section with three phase conductors arranged in a triangle, and three smaller earth conductors positioned in the spaces between the phase conductors, creating a six-pointed star pattern (three main points for phase, three intermediate points for earth). This symmetric arrangement ensures that from any point in space, the three phase conductors are at equal geometric distances, and the three earth conductors are equally distributed around them. The electric field created by the phase conductors is therefore balanced\u2014there is no preferential direction where the field is stronger or weaker.<\/p>\n\n<p>When this symmetric cable is subjected to PWM common-mode voltage, the high-frequency field couples equally to the motor rotor from all three phases. The rotor experiences a uniform potential with respect to the symmetric earth reference. Rather than creating asymmetric zero-sequence currents that concentrate in hot spots, the symmetric design distributes any current that does flow uniformly around the rotor surface and through the bearings. This distributed current density is far below the threshold needed to create arcing and EDM damage.<\/p>\n\n<p>This is the fundamental principle behind (N)3GHSSYCY’s effectiveness: symmetry in cable geometry creates symmetry in field distribution, which eliminates the asymmetric currents that cause bearing damage. This is not magic\u2014it is applied electromagnetic geometry, proven through theory and field experience.<\/p>\n\n<\/article>\n\n<article>\n\n<h2 id=\"s7\">7. Dual Shielding: Aluminum Foil and Tinned Copper Braid Working Together <span class=\"cn\">\u53cc\u5c4f\u853d\uff1a\u94dd\u7b94\u548c\u9540\u9521\u94dc\u7f16\u7ec7\u7f51\u5171\u540c\u5de5\u4f5c<\/span><\/h2>\n\n<p>Beyond the symmetric conductor arrangement, (N)3GHSSYCY cables incorporate dual shielding\u2014aluminum foil plus tinned copper braid\u2014that provides multiple benefits working together as an integrated system.<\/p>\n\n<p>The aluminum foil shield (in combination with polyester backing) provides high-frequency attenuation and continuity. The foil completely surrounds the conductor group, providing 100% coverage that prevents high-frequency radiation outward from the cable and prevents external high-frequency noise from coupling inward. For frequencies in the megahertz range where the cable is at risk of both radiating EMI (electromagnetic interference) outward into the surrounding environment and receiving coupled noise from equipment, the complete foil barrier is essential.<\/p>\n\n<p>However, the aluminum foil alone, while excellent for attenuation, is not sufficient for low-impedance current return. Aluminum has relatively high resistivity compared to copper, and the thin foil has significant resistance at high frequencies. When high-frequency common-mode current seeks a return path to the variable frequency drive, the aluminum foil alone cannot provide sufficiently low impedance. The tinned copper braid\u2014typically with 85%+ coverage\u2014provides the low-impedance path that high-frequency current needs to find its way back to the drive without flowing through the motor rotor and bearings.<\/p>\n\n<p>The two shields work together: the foil provides electromagnetic containment and attenuation, while the copper braid provides a low-impedance current return highway. Neither shield alone would be fully effective. The foil without the braid would prevent radiation but would not provide adequate current return paths, potentially forcing high-frequency current through the motor. The braid without the foil would provide current return but would not adequately attenuate radiation and noise. The dual shielding configuration combines the best properties of each.<\/p>\n\n<\/article>\n\n<article>\n\n<h2 id=\"s8\">8. The Absolute Requirement for Dual 360-Degree Shielding Grounding <span class=\"cn\">\u53cc 360 \u5ea6\u5c4f\u853d\u63a5\u5730\u7684\u7edd\u5bf9\u8981\u6c42<\/span><\/h2>\n\n<p>The most critical, and most frequently overlooked, requirement for (N)3GHSSYCY cable performance is proper grounding of the shielding at both ends. This requirement is so critical that it deserves its own section, because improper grounding completely negates the cable’s protective benefits.<\/p>\n\n<p>In low-frequency applications (60 Hz power distribution), shielding is often grounded at only one end to prevent ground loops. The reasoning is sound for low-frequency: a ground loop at power frequency creates a circulating current that wastes energy and creates harmonics. Single-end grounding prevents this loop and is standard practice for power cables.<\/p>\n\n<p>However, at the megahertz frequencies present in VFD common-mode voltage, single-end grounding creates a catastrophic problem: the shielding becomes a giant radiation antenna. When high-frequency current flows into the shield at one end, with no return path at the other end, the shield resonates electrically and radiates the high-frequency energy outward as electromagnetic interference. Moreover, the lack of a return path means that high-frequency current cannot flow back through the shield. Instead, the current seeks alternative return paths through the motor rotor, the bearings, and the motor frame\u2014exactly the paths that create bearing damage.<\/p>\n\n<p>Proper VFD cable grounding requires 360-degree continuous shielding connection at both the variable frequency drive end and the motor end. This means that the entire circumference of the shield must be connected to ground at both termination points, not just a single contact point. This is typically accomplished using proper EMC cable glands that wrap around the entire circumference of the shield and make continuous electrical contact. Any break in this 360-degree connection defeats the purpose and creates a radiation point where high-frequency energy can escape or where current can flow into unintended paths.<\/p>\n\n<p>This is not a recommendation or best practice\u2014it is an absolute requirement. If you cannot achieve 360-degree dual grounding, the (N)3GHSSYCY cable will not protect the motor from bearing pitting. In fact, a partially shielded cable that is not properly grounded can be worse than no shielding at all, because it attenuates lower-frequency noise while allowing megahertz-frequency noise to radiate unchecked.<\/p>\n\n<\/article>\n\n<article>\n\n<h2 id=\"s9\">9. Capacitive Coupling Reduction Through Low-Mutual-Capacitance Design <span class=\"cn\">\u901a\u8fc7\u4f4e\u4e92\u5bb9\u8bbe\u8ba1\u964d\u4f4e\u5bb9\u6027\u8026\u5408<\/span><\/h2>\n\n<p>In addition to the symmetric conductor arrangement and dual shielding, (N)3GHSSYCY cables incorporate design features that reduce the mutual capacitance between phase conductors and between phase conductors and ground. This is measured and specified in the cable technical data\u2014typically 30% lower capacitance than conventional cables.<\/p>\n\n<p>Lower mutual capacitance means that less capacitive current flows in response to the high-frequency common-mode voltage. Capacitive current is directly proportional to the rate of voltage change (dv\/dt) and the capacitance: I = C \u00d7 dv\/dt. By reducing C (capacitance), you reduce the resulting capacitive current, which reduces the current flowing through the motor rotor and bearings. This reduces the magnitude of the arcing and EDM damage that occurs.<\/p>\n\n<p>The lower capacitance is achieved through careful engineering of the cable’s dielectric materials and geometry. The cable uses materials with lower permittivity, and the conductor spacing is optimized to minimize the electric field strength between phase conductors. These changes require precise manufacturing control and represent one of the reasons that proper VFD cables cost more than conventional industrial cables. You cannot achieve low mutual capacitance through casual cable design\u2014it requires disciplined engineering.<\/p>\n\n<\/article>\n\n<article>\n\n<h2 id=\"s10\">10. Continuous Ampacity for (N)3GHSSYCY in Inverter Duty Service <span class=\"cn\">\u53d8\u9891\u5668\u5de5\u51b5\u4e0b (N)3GHSSYCY \u7684\u8fde\u7eed\u8f7d\u6d41\u91cf<\/span><\/h2>\n\n<p>Having examined the electromagnetic design principles, we can now address the electrical performance specifications. The continuous ampacity of (N)3GHSSYCY 3×150+3×25 cables at reference conditions is 320 amperes according to DIN VDE 0250-813.<\/p>\n\n<p>However, VFD service introduces thermal considerations different from conventional power systems. The PWM waveform contains high-frequency harmonic content that increases losses in both the cable and the motor compared to sinusoidal AC. Additionally, the variable frequency drive may operate at lower motor speeds during certain process steps, reducing natural cooling of the motor. These factors require derating the cable’s ampacity compared to the reference value.<\/p>\n\n<p>For VFD service, a thermal derating factor of 0.9\u20130.95 is typical, representing a 5\u201310% reduction from the reference ampacity. A 320-ampere cable would therefore be designed for approximately 300\u2013290 amperes continuous in typical VFD service. This derating accounts for the additional thermal stress from PWM harmonics without requiring cable oversizing.<\/p>\n\n<\/article>\n\n<article>\n\n<h2 id=\"s11\">11. Long Cable Runs and Voltage Reflection: When Filtering Becomes Mandatory <span class=\"cn\">\u957f\u7535\u7f06\u6577\u8bbe\u548c\u7535\u538b\u53cd\u5c04\uff1a\u4f55\u65f6\u8fc7\u6ee4\u53d8\u4e3a\u5f3a\u5236\u6027<\/span><\/h2>\n\n<p>One critical application limitation of (N)3GHSSYCY cables that engineers must understand is the maximum recommended cable length. When the cable run exceeds approximately 50\u2013100 meters, depending on the drive model and motor characteristics, PWM pulse reflections become significant.<\/p>\n\n<p>Here is why: the PWM pulse traveling along the cable encounters the motor as a load. The impedance of the motor is different from the cable’s characteristic impedance, so part of the pulse reflects backward toward the drive. This reflected pulse can add constructively with the forward-traveling pulse, creating voltage doubling or even tripling at the motor terminals. In extreme cases, the peak voltage at the motor terminals can reach twice the drive’s DC bus voltage, far exceeding the motor insulation rating. When this occurs, the motor winding insulation can fail, or severe electromagnetic stress can accelerate other failure modes including bearing pitting.<\/p>\n\n<p>If cable runs must exceed the maximum recommended length, the solution is to install a sine-wave filter at the drive output or a dv\/dt choke that limits the rate of voltage change and prevents pulse doubling. These filters are not optional equipment for long cables\u2014they are engineering requirements that must be specified as part of the system design.<\/p>\n\n<\/article>\n\n<article>\n\n<h2 id=\"s12\">12. Critical Installation Errors That Negate Cable Protective Benefits <span class=\"cn\">\u524a\u5f31\u7535\u7f06\u4fdd\u62a4\u4f18\u52bf\u7684\u5173\u952e\u5b89\u88c5\u9519\u8bef<\/span><\/h2>\n\n<p>The most tragic failure scenario occurs when an engineer specifies the correct (N)3GHSSYCY cable and dual shielding, but field installation errors prevent the cable from delivering its intended protection. Understanding these common mistakes helps prevent failures after the cable has been properly selected.<\/p>\n\n<h3>12.1 Single-End or Inadequate Shielding Grounding <span class=\"cn\">\u5355\u7aef\u6216\u4e0d\u8db3\u7684\u5c4f\u853d\u63a5\u5730<\/span><\/h3>\n\n<p>Installers trained on conventional power distribution cables often ground the shield at only one end, following the ground-loop prevention principle that is appropriate for low-frequency applications. On a VFD system, this single-end grounding creates an antenna effect that radiates high-frequency noise and prevents proper current return, completely negating the shield’s protective value. Every VFD cable installation must be verified to have 360-degree grounding at both ends using proper EMC glands.<\/p>\n\n<h3>12.2 Improper Cable Termination and Shielding Connection <span class=\"cn\">\u4e0d\u5f53\u7684\u7535\u7f06\u7ec8\u7aef\u548c\u5c4f\u853d\u8fde\u63a5<\/span><\/h3>\n\n<p>The connection between the cable shield and the grounding system must be made with proper EMC connectors designed for high-frequency shielding, not with standard cable glands or improvised connections. Improper terminations create high-impedance connections that prevent high-frequency current from returning through the shield, forcing it through the motor rotor instead.<\/p>\n\n<h3>12.3 Cable Separation and Routing Errors <span class=\"cn\">\u7535\u7f06\u5206\u79bb\u548c\u5e03\u7ebf\u9519\u8bef<\/span><\/h3>\n\n<p>If (N)3GHSSYCY cables are routed closely alongside conventional power cables or control cables, coupling can occur that defeats the symmetry and shielding. The cable must be maintained at least 150\u2013300 mm away from other cables, and it must not be bundled with conventional cables in cable trays. Proper cable separation must be maintained throughout the installation.<\/p>\n\n<\/article>\n\n<article>\n\n<h2 id=\"s13\">13. Field Commissioning and Verification Procedures <span class=\"cn\">\u73b0\u573a\u6295\u8fd0\u548c\u9a8c\u8bc1\u7a0b\u5e8f<\/span><\/h2>\n\n<p>After installation, several commissioning procedures should be performed to verify that the cable system is functioning as designed and providing motor protection.<\/p>\n\n<h3>13.1 Shielding Continuity Verification <span class=\"cn\">\u5c4f\u853d\u8fde\u7eed\u6027\u9a8c\u8bc1<\/span><\/h3>\n\n<p>Use a multimeter to verify that the shield has continuous electrical connection from the drive to the motor. The resistance should be less than 0.1 ohms. Significantly higher resistance indicates poor connections that will impede high-frequency current return.<\/p>\n\n<h3>13.2 Ground Loop Current Measurement <span class=\"cn\">\u5730\u73af\u7535\u6d41\u6d4b\u91cf<\/span><\/h3>\n\n<p>Using a clamp meter on the shield return conductor, measure any circulating current due to ground loops. For VFD cables with dual-end grounding, some ground loop current is expected and acceptable (typically <1 ampere). If ground loop current exceeds 5\u201310 amperes continuously, investigate and correct the grounding configuration.<\/p>\n\n<h3>13.3 Motor Bearing Temperature Trending <span class=\"cn\">\u7535\u673a\u8f74\u627f\u6e29\u5ea6\u8d8b\u52bf\u5206\u6790<\/span><\/h3>\n\n<p>During the first weeks of operation, monitor motor bearing temperature continuously. Proper EMC protection should keep bearing temperature within the motor manufacturer’s specification. If bearing temperature rises unexpectedly or continues rising over time, stop operation and investigate the cause. Bearing temperature rise is often the first indicator that the motor is experiencing damaging currents.<\/p>\n\n<\/article>\n\n<\/article>\n\n\n<section class=\"sources\" id=\"s14\">\n<h2>References & Standards <span class=\"cn\">\u53c2\u8003\u6587\u732e\u4e0e\u6807\u51c6<\/span><\/h2>\n<ol>\n<li>DIN VDE 0250-813 \u2014 “Heavy-Duty Flexible Rubber-Sheathed Cables.” European standard establishing specifications for flexible industrial cables including (N)3GHSSYCY types for variable frequency drive applications.<\/li>\n<li>IEEE 1415 \u2014 “IEEE Guide for Induction Machinery Maintenance Testing and Failure Analysis.” Technical reference describing bearing pitting failure modes, diagnostic procedures, and mitigation strategies for VFD-driven motors.<\/li>\n<li>IEC 61800-3 \u2014 “Adjustable Speed Electrical Power Drive Systems \u2014 Part 3: EMC Requirements and Specific Test Methods.” International standard establishing EMC requirements for variable frequency drives and associated cabling.<\/li>\n<li>Siemens Sinamics Installation Manuals \u2014 Detailed specifications for cable requirements, shielding grounding procedures, and commissioning verification for Siemens VFD systems.<\/li>\n<li>ABB Drives Technical Handbook \u2014 Comprehensive reference on motor bearing protection, common-mode voltage characteristics, and cable specification guidelines for ABB variable frequency drive systems.<\/li>\n<li>(N)3GHSSYCY Technical Data Sheet \u2014 Manufacturer specifications including ampacity ratings, mutual capacitance measurements, shielding effectiveness data, and installation procedures.<\/li>\n<\/ol>\n<\/section>\n\n\n<section class=\"contact\">\n<h2>Contact Feichun Cable Technical Support <span class=\"cn\">\u8054\u7cfb\u98de\u7eaf\u7535\u7f06\u6280\u672f\u652f\u6301<\/span><\/h2>\n<p style=\"font-size:.88rem;color:var(--tx2);margin-bottom:4px\">For (N)3GHSSYCY and other VFD motor cable specifications, bearing pitting prevention system design, EMC shielding and grounding architecture consulting, dual-end 360-degree shielding connection design and verification, ampacity calculations for inverter duty cycles, cable filtering and dv\/dt choke selection for long cable runs, installation procedure development and quality assurance protocols, field commissioning and verification procedures, motor bearing protection monitoring and troubleshooting, or comprehensive technical documentation for drive system safety certification and compliance, contact our technical engineering team. We provide detailed EMC analysis per IEC 61800-3 standards, motor bearing protection system design accounting for shaft voltage and capacitive coupling, dual shielding architecture design and termination specifications, field installation and commissioning guidelines, and complete documentation for reliable variable frequency drive system implementation with optimized motor protection and extended bearing life. <span class=\"cn\">\u5bf9\u4e8e\u53d8\u9891\u7535\u673a\u8f74\u627f\u4fdd\u62a4\u7535\u7f06\u7684\u9009\u578b\u3001EMC \u63a5\u5730\u8bbe\u8ba1\u6216\u73b0\u573a\u5b89\u88c5\u9a8c\u8bc1\uff0c\u8bf7\u76f4\u63a5\u8054\u7cfb\u6211\u4eec\u7684\u6280\u672f\u56e2\u961f\u3002<\/span><\/p>\n<div class=\"cg\">\n<div class=\"cc\">\n<div class=\"lb\">Email <span class=\"cn\">\u7535\u5b50\u90ae\u4ef6<\/span><\/div>\n<div class=\"vl\"><a href=\"mailto:Tech@feichuncables.com\">Tech@feichuncables.com<\/a><\/div>\n<\/div>\n<div class=\"cc\">\n<div class=\"lb\">Service <span class=\"cn\">\u670d\u52a1<\/span><\/div>\n<div class=\"vl\">Variable Frequency Drive Motor Power Systems<\/div>\n<\/div>\n<div class=\"cc\">\n<div class=\"lb\">Specialization <span class=\"cn\">\u4e13\u4e1a<\/span><\/div>\n<div class=\"vl\">(N)3GHSSYCY cables, bearing pitting prevention, EMC shielding, VFD system certification<\/div>\n<\/div>\n<\/div>\n<\/section>\n\n<footer>\n<p>© 2026 Feichun Cable Technical Division <span class=\"cn\">\u98de\u7eaf\u7535\u7f06\u6280\u672f\u90e8<\/span>. All rights reserved.<\/p>\n<p style=\"margin-top:5px\">Variable Frequency Drive Motor Power Cable Engineering | <a href=\"https:\/\/feichuncables.com\" rel=\"nofollow\" target=\"_blank\" style=\"color:var(--ac)\">feichuncables.com<\/a><\/p>\n<\/footer>\n<\/div>\n<\/body>\n<\/html>\n","protected":false},"excerpt":{"rendered":"In the industrial drive systems community, a troubling pattern has emerged over the past 15\u201320 years: motors operating with variable frequency drives (VFDs) are failing prematurely at rates far exceeding what was experienced with motors running on direct line power. The most common failure mode is not overheating, not insulation breakdown, but rather bearing pitting\u2014a surface degradation of the rolling elements and races in motor bearings that develops progressively until the bearing becomes non-functional. Engineers initially thought this was merely a cable size issue or a thermal management problem. More careful investigation revealed the true cause: electromagnetic phenomena unique to high-frequency PWM switching were creating conditions that slowly eroded bearing surfaces through electrical discharge machining (EDM). The solution required not larger cables or better cooling, but specifically engineered cables with symmetric conductor geometry and dual shielding designed to control the electromagnetic environment inside the motor. Understanding this problem and its solution requires learning about electromagnetic phenomena that many motor engineers were never formally taught\u2014the behavior of common-mode voltage, shaft voltage, and capacitive coupling in high-frequency environments. This is not obscure physics for academics; it is practical engineering knowledge that determines whether motors survive their design life or fail prematurely after 2\u20133 years of operation.","protected":false},"author":1,"featured_media":7687,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"csco_singular_sidebar":"left","csco_page_header_type":"title","csco_page_load_nextpost":"","footnotes":""},"categories":[66,94,464],"tags":[],"class_list":["post-7686","post","type-post","status-publish","format-standard","has-post-thumbnail","category-common-problems-encountered-in-cable-applications","category-din-vde-0250-mining-cable","category-flexible-cables-with-high-bending-life-and-fatigue-resistance","cs-entry"],"_links":{"self":[{"href":"https:\/\/feichuncables.com\/blog\/wp-json\/wp\/v2\/posts\/7686","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/feichuncables.com\/blog\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/feichuncables.com\/blog\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/feichuncables.com\/blog\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/feichuncables.com\/blog\/wp-json\/wp\/v2\/comments?post=7686"}],"version-history":[{"count":2,"href":"https:\/\/feichuncables.com\/blog\/wp-json\/wp\/v2\/posts\/7686\/revisions"}],"predecessor-version":[{"id":7689,"href":"https:\/\/feichuncables.com\/blog\/wp-json\/wp\/v2\/posts\/7686\/revisions\/7689"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/feichuncables.com\/blog\/wp-json\/wp\/v2\/media\/7687"}],"wp:attachment":[{"href":"https:\/\/feichuncables.com\/blog\/wp-json\/wp\/v2\/media?parent=7686"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/feichuncables.com\/blog\/wp-json\/wp\/v2\/categories?post=7686"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/feichuncables.com\/blog\/wp-json\/wp\/v2\/tags?post=7686"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}

{"id":7686,"date":"2026-02-28T10:30:37","date_gmt":"2026-02-28T02:30:37","guid":{"rendered":"https:\/\/feichuncables.com\/blog\/?p=7686"},"modified":"2026-02-28T10:30:43","modified_gmt":"2026-02-28T02:30:43","slug":"vfd-motor-bearings-why-do-siemens-variable-frequency-drives-require-n3ghssycy-3x1503x25-to-prevent-bearing-pitting","status":"publish","type":"post","link":"https:\/\/feichuncables.com\/blog\/vfd-motor-bearings-why-do-siemens-variable-frequency-drives-require-n3ghssycy-3x1503x25-to-prevent-bearing-pitting\/","title":{"rendered":"VFD Motor Bearings: Why do Siemens variable frequency drives require (N)3GHSSYCY 3×150+3×25 to prevent bearing pitting?"},"content":{"rendered":"\n