[email protected]

радиус изгиба

9 Min Read
H07RN-F: Advanced High-Flexibility Salt-Fog Resistant Port Cable Engineering Solution Specialized rubber-sheathed electrical cable engineered for extreme maritime and coastal port environments. H07RN-F combines superior mechanical flexibility (4×D minimum fixed-laying bending radius, 6×D flexible-application capability) with comprehensive salt-fog environmental resistance, enabling reliable 450/750V power distribution and control signaling in container gantry systems, ship loaders, and port automation infrastructure where conventional cables fail within 6–12 months of deployment.
Technical Department
on16/06/2026

Technical Data для mining и tunnelling cables: буквенная кодировка, свойства материалов, радиусы изгиба, сопротивление, токовая нагрузка и причины отказов

Этот технический раздел объединяет letter coding of cable types, механические свойства изоляционных и оболочечных материалов по DIN VDE 0207, минимальные радиусы изгиба, сопротивление и токовые нагрузки проводников mining cables, корректирующие коэффициенты температуры, причины отказов tunnelling cables, типовые ошибки splice / termination и правила обращения с кабельными барабанами.
7 Min Read
UNE 22512 — formally titled "Cables flexibles para minería subterránea con tensiones de 1,8/3 kV y 0,6/1 kV con aislamiento de caucho, con armadura" (Flexible cables for underground mining, rubber-insulated, armoured) — exists as a parallel but fundamentally distinct standard from its unarmoured sibling UNE 22511. Where UNE 22511 is engineered as a torsion-optimized drag cable for mobile equipment, UNE 22512 is engineered as a crush-and-cut protected feeder cable for semi-fixed installations where mechanical damage from external forces (falling rock, equipment impact, floor pressure) is a documented operational risk, but the extreme torsional loading of continuously moving equipment is not. The addition of metallic armour — specifically, galvanized steel wire braid forming what the standard designates as M2 GSWB — is the defining structural choice that reshapes every downstream design decision in the cable. The armour is not merely a protective layer added to an otherwise standard cable; rather, it fundamentally alters the cable's mechanical behavior, installation requirements, cost structure, and applicable fatigue loading regimes. Understanding UNE 22512 therefore requires understanding not just what the armour is, but why its presence necessitates a completely different engineering philosophy compared to unarmoured cables. The standard was developed by AENOR (Asociación Española de Normalización y Certificación) to address a specific operational problem encountered in Spanish and Latin American underground mining installations. While drag cables experience cyclic torsional loading as the controlling mechanical stress, semi-fixed installation cables experience something categorically different: static or low-cycle crushing and cutting stresses from external impacts, combined with continuous exposure to abrasive underground surfaces and sharp rock edges. A cable optimized exclusively for torsional fatigue — such as UNE 22511 — when installed in a semi-fixed route subject to crushing and cutting, experiences mechanical failure not through fatigue mechanisms but through acute sheath penetration, insulation damage, and moisture ingress. Conversely, an armoured cable optimized for crush protection, if inappropriately installed in a drag duty application, fails not through crushing (which the armour prevents) but through torsional fatigue of the armour wires themselves — a more insidious failure mode that occurs entirely within the armour structure, invisible until complete armour failure exposes the underlying insulation.
Technical Department
on15/06/2026

卷筒电缆技术手册操作安装与电气

本手册中的弯曲半径、载流量、降容系数、压降与短路数据,依据 DIN VDE 0298-4、VDE 0250、IEC 等公开标准的通用工程值,适用于一般卷筒/移动电缆的技术说明与方案初选。具体工程须按项目实际工况核算;飞纯具体产品的型号、外径、重量、电缆盘规格等参数,以飞纯正式产品规格书与实测数据为准。安装应由专业人员执行,并参照适用标准与现场条件。
5 Min Read
(N)GRDGÖU-J Nomenclature (VDE 0250 part 813): (N) = Nominal voltage prefix (0.6/1 kV implicit in designation) G = Gummiert (rubber-insulated) R = Rubber outer sheath D = Dynamisch (dynamic/flexing application) G = Gummiert inner sheath (intermediate layer) Ö = German standard designation (ö indicates European origin) U = Unarmoured (no metal sheath) J = Jacked (multi-sheath design: intermediate + outer) Full meaning: Rubber-insulated, rubber-sheathed, dynamic-rated, multi-sheath construction, unarmoured festoon cable VDE 0250 part 813 scope: Published by: VDE (Verband der Elektrotechnik, German standards body) Applies to: Flexible cables for crane installations (particularly festoon systems) Coverage: Voltage, temperature, mechanical properties, installation methods Festoon-specific requirements: - High bending flexibility (4×D minimum typical) - Fast rewind capability (240+ m/min rated speed) - Sustained torsion tolerance (±25°/1m continuous) - Extended temperature range (−50 to +80°C) - UV/ozone/moisture resistance (outdoor exposure) Alternate designations (similar cables): IEC 60811-1-1: International equivalent (less specific) DIN VDE 0298 part 3: German mechanical property standard DIN VDE 0482-265-2-1: German flame test standard EN 50265-2-1: European flame test equivalent GRDGÖU-J advantage: Combines all standards into single VDE designation Procurement simplified for European buyers
Technical Department
on12/06/2026

PANZERFLEX-L 0,6/1 kV (N)SHTÖU-J / -O: резиновые силовые кабели для кабельных барабанов и фестонных систем

PANZERFLEX-L 0,6/1 kV (N)SHTÖU-J / -O — это гибкие силовые резиновые кабели, предназначенные для подвижных механизмов, кабельных барабанов и фестонных систем, работающих при высоких механических нагрузках, частом изгибе, кручении, быстром движении и сильном ускорении.
9 Min Read
FLEXIFESTOON® HF-FLAT CY: Advanced Screened Halogen-Free Flat Cable System for Industrial Automation, Variable Frequency Drives, and EMI-Critical Control Systems 0.6/1 kV Shielded Power and Control Cable | Red Copper Braid EMI/RFI Protection | Electromagnetic Signal Integrity | Low Smoke Emission | Nuclear Plant Certified Electromagnetic Shielding Halogen-Free Extended Temperature Signal Integrity Modern industrial automation environments are under siege from electromagnetic interference (EMI). Variable frequency drives (VFDs), inverters, switched-mode power supplies, and wireless control systems generate broadband electromagnetic noise creating a hostile environment for signal integrity and cable performance. Conventional unshielded festoon cables, adequate for simple motor-contactor systems, fail catastrophically when deployed in VFD-driven installations—electromagnetic coupling generates false signals, nuisance equipment trips, and progressive insulation degradation. Feichun's FLEXIFESTOON® HF-FLAT CY introduces revolutionary screened flat cable architecture combining comprehensive red copper braid electromagnetic shielding, halogen-free safety chemistry, and parallel core stranding optimized for electromagnetic signal protection in industrial automation systems. This technical examination explores electromagnetic interference mechanisms, shielding design principles, VFD compatibility architecture, and operational deployment advantages of the industry's most comprehensive EMI-protected flat festoon cable platform.
Technical Department
on12/06/2026

Что такое ÖLFLEX® FIRE 6387 MC: инженерный анализ огнестойкого многожильного силового кабеля 0.6/1 kV

ÖLFLEX® FIRE 6387 MC — это fire resistant multicore power cable с номинальным напряжением U0/U 600/1000 V. Кабель специально разработан для wiring applications в critical life safety systems общественных и промышленных зданий, включая airports, hotels, hospitals, subways, train stations, building management systems, emergency lighting, standby power supplies, lifts and elevators. Конструкция включает stranded plain annealed copper wire, mica based fire resistance tape, XLPE insulation and LSHF outer sheath. Цвет кабеля — orange.
14 Min Read
LIFT-2S (European) vs. LIFT-1S UL (North American): LIFT-2S characteristics: Voltage: 300/500V (European standard, lower voltage) Temperature: −40°C to +70°C (moderate range) Standards: VDE 0482 part 265-2-1, EN 50265-2-1, IEC 60332-1-2 Design philosophy: Safety by material redundancy (2 steel cores) Steel cores: 2× cores provide mechanical backup Conductor: Class 6 (European, ~150–200 wires per mm²) Cost: Lower (proven European manufacturing) Market: Europe, Asia-Pacific, most of world LIFT-1S UL characteristics: Voltage: 600V (North American standard, higher voltage) Temperature: −25°C to +105°C (extreme range, high-temp optimized) Standards: UL 2562, UL 62, CSA C22.2 No.210.2 Design philosophy: Safety by certification (single core + redundant control) Steel core: 1× core (sufficient with nylon covering) Conductor: Class M (UL, extra fine ~300+ wires per mm²) Cost: Higher (UL testing, certification documentation) Market: North America (USA, Canada), Mexico UL 2562 specialty certification: UL 2562 scope: Elevator and Dumbwaiter Cables Specific requirements: 1. Pendant cable design (cable hangs freely, no duct support) 2. Vertical orientation (designed for gravity-loaded suspension) 3. Repeated flex cycles (cable moves up/down frequently) 4. Safety-critical function (failure = personnel risk) Consequence: More stringent than general-purpose cables Testing includes: Bend cycle fatigue, heat aging, compression resistance Test procedures (unique to UL 2562): Bend cycle test: 1,000+ cycles at minimum bending radius Cable must pass insulation resistance after cycling Heat aging: 500+ hours at 105°C continuous Tensile strength retention minimum 70% Compression: 1,000+ hours under sustained compression Cable cross-section must not exceed 5% permanent deformation LIFT-2S (no UL 2562): Tests per VDE are less stringent on fatigue/cycling Assumes cable mostly static, not repeated flex Adequate for European elevator duty (lower speed, fewer cycles) LIFT-1S UL: All UL 2562 tests passed (proven for North American elevators) Faster cycle times, more frequent motion → more fatigue stress Extra testing ensures reliability under North American elevator duty Market requirement (regulatory): Europe/International: CE mark required (European conformity) VDE/EN/IEC standards sufficient No UL certification needed (not recognized in EU) LIFT-2S is sufficient North America (USA, Canada): UL certification mandatory for elevators UL 2562 specifically for elevator cables CSA dual certification required in Canada LIFT-2S NOT acceptable (lacks UL 2562) LIFT-1S UL mandatory Cost implication: UL certification: ~$5,000–15,000 per product per region Testing duration: 3–6 months per model Documentation: Comprehensive test reports, technical files Result: LIFT-1S UL 20–30% higher cost than equivalent European cable
Technical Department
on12/06/2026

Что такое ÖLFLEX® INSTRUM RE-2X(ST)YRY: инженерный анализ армированного инструментального кабеля с XLPE изоляцией и общим экраном

ÖLFLEX® INSTRUM RE-2X(ST)YRY — это armoured instrumentation cable с XLPE core insulation, overall screen, PVC inner sheath, galvanized steel wire armour and PVC outer sheath. Кабель предназначен для communication, data and voice transmission signal в industrial process manufacturing plants, Oil and Gas industry and petrochemical industry. По предоставленным данным он основан на EN 50288-7, имеет flame retardance according to IEC 60332-3-24, stranded plain annealed copper wires according to BS 6360 / IEC 60228 Class 2, aluminium polyester tape collective screen, tinned copper drain wire, black PVC inner sheath and black or blue PVC outer sheath.
13 Min Read
FLEXIFESTOON® SEOOW YELLOW represents FeiChun's entry into the low-voltage festoon and temporary power market. The nomenclature requires careful explanation to distinguish this product from the high-voltage FLEXIDRUM series: FLEXIFESTOON Product Nomenclature: FLEXIFESTOON® = Product family name Flex = Flexible (emphasis on bending & handling) Festoon = Strung overhead in continuous runs (typical festoon lighting application) SEOOW = Industry-standard designation S = Service cord (temporary, not permanent installation) E = Elastomer jacket (flexible sheath) OO = Oil-resistant conductor insulation (TPE qualifies as oil-resistant) W = Weather-resistant sheath (water, ozone, UV resistant) SEOOW is defined in: UL 62 (Standard for Flexible Cords and Cables) CSA 22.2 No. 49 (Canadian equivalent) NFPA 70 National Electrical Code (NEC) Article 400 YELLOW designation: Color: RAL 1021 (traffic yellow, high visibility) Safety significance: Yellow cords attract attention in job sites Practical purpose: Easy to identify, prevent trips/entanglement Contrast with FLEXIDRUM series: FLEXIDRUM (High-Voltage MV Cable): Voltage: 3.6 kV to 20/35 kV (power distribution) Temperature: −40 to +80°C (standard industrial) Application: Mobile mining/tunneling equipment (capital-intensive) Size: Large diameter, heavy (3–12 kg/km) FLEXIFESTOON (Low-Voltage Service Cord): Voltage: 600V (light/power temporary use) Temperature: −60 to +105°C (extreme environmental range) Application: Festoon lighting, temporary site power, outdoor events Size: Small diameter, lightweight (0.05–0.3 kg/m) Cost: Consumer/contractor-grade (not specialty industrial)
Technical Department
on12/06/2026

Что такое ÖLFLEX ROBOT 915 450/750V: высокогибкий одножильный роботный кабель для динамического изгиба и кручения

ÖLFLEX ROBOT 915 — это высокогибкий одножильный кабель 450/750V для промышленных роботов, портального роботизированного оборудования, автоматизированных манипуляторов, кабельных цепей и подвижных машинных узлов, где кабель одновременно испытывает динамический изгиб, кручение, вибрацию, контакт с маслами и ограниченное монтажное пространство. В инженерной логике Feichun этот класс кабеля важен не как обычный одиночный провод питания, а как механически нагруженный элемент робота: он должен работать внутри dress pack, проходить через изгибающуюся руку, выдерживать torsion motion до ±180°/м и сохранять электрическую надёжность на протяжении миллионов циклов.
10 Min Read
LIFT-2S (European) vs. LIFT-1S UL (North American): LIFT-2S characteristics: Voltage: 300/500V (European standard, lower voltage) Temperature: −40°C to +70°C (moderate range) Standards: VDE 0482 part 265-2-1, EN 50265-2-1, IEC 60332-1-2 Design philosophy: Safety by material redundancy (2 steel cores) Steel cores: 2× cores provide mechanical backup Conductor: Class 6 (European, ~150–200 wires per mm²) Cost: Lower (proven European manufacturing) Market: Europe, Asia-Pacific, most of world LIFT-1S UL characteristics: Voltage: 600V (North American standard, higher voltage) Temperature: −25°C to +105°C (extreme range, high-temp optimized) Standards: UL 2562, UL 62, CSA C22.2 No.210.2 Design philosophy: Safety by certification (single core + redundant control) Steel core: 1× core (sufficient with nylon covering) Conductor: Class M (UL, extra fine ~300+ wires per mm²) Cost: Higher (UL testing, certification documentation) Market: North America (USA, Canada), Mexico UL 2562 specialty certification: UL 2562 scope: Elevator and Dumbwaiter Cables Specific requirements: 1. Pendant cable design (cable hangs freely, no duct support) 2. Vertical orientation (designed for gravity-loaded suspension) 3. Repeated flex cycles (cable moves up/down frequently) 4. Safety-critical function (failure = personnel risk) Consequence: More stringent than general-purpose cables Testing includes: Bend cycle fatigue, heat aging, compression resistance Test procedures (unique to UL 2562): Bend cycle test: 1,000+ cycles at minimum bending radius Cable must pass insulation resistance after cycling Heat aging: 500+ hours at 105°C continuous Tensile strength retention minimum 70% Compression: 1,000+ hours under sustained compression Cable cross-section must not exceed 5% permanent deformation LIFT-2S (no UL 2562): Tests per VDE are less stringent on fatigue/cycling Assumes cable mostly static, not repeated flex Adequate for European elevator duty (lower speed, fewer cycles) LIFT-1S UL: All UL 2562 tests passed (proven for North American elevators) Faster cycle times, more frequent motion → more fatigue stress Extra testing ensures reliability under North American elevator duty Market requirement (regulatory): Europe/International: CE mark required (European conformity) VDE/EN/IEC standards sufficient No UL certification needed (not recognized in EU) LIFT-2S is sufficient North America (USA, Canada): UL certification mandatory for elevators UL 2562 specifically for elevator cables CSA dual certification required in Canada LIFT-2S NOT acceptable (lacks UL 2562) LIFT-1S UL mandatory Cost implication: UL certification: ~$5,000–15,000 per product per region Testing duration: 3–6 months per model Documentation: Comprehensive test reports, technical files Result: LIFT-1S UL 20–30% higher cost than equivalent European cable
Technical Department
on11/06/2026

Что такое ÖLFLEX® 100 I: инженерный анализ ISI-маркированного ПВХ-кабеля до 1100 V

ÖLFLEX® 100 I — это ISI-маркированный ПВХ-кабель для plant engineering, installation, industrial machinery, air-conditioning power circuits, main power circuits to individual apartments and dry or damp interiors under medium mechanical load conditions. По предоставленным данным кабель построен на тонкопроволочных голых медных жилах class 5 по IS 8130-1984, имеет ПВХ-изоляцию, наружную оболочку PVC или PVC FR-LSH по IS 694:2010, номинальное напряжение до 1100 V и повышенную электрическую прочность за счёт испытательного напряжения 3 kV.
16 Min Read
Reeling & Trailing Cables for Cranes & Mining — Feichun Special Cable Blogs
Technical Department
on11/06/2026

Что такое ÖLFLEX® TRAY II CY: экранированный Control Cable 0.6/1kV UL TC-ER 600V AWM WET OIL/SUN RES TRAY — инженерный анализ для промышленного оборудования, WTG, портов и тяжёлой техники

ÖLFLEX® TRAY II CY — это экранированный control cable класса 0.6/1 kV, предназначенный для промышленного машиностроения, plant engineering, кабельных лотков в США, tool machines, outdoor use, direct burial, wind turbine tray cable applications и EMC-sensitive environments. Его техническая ценность заключается в редком сочетании: UL TC-ER 600V, AWM WET, OIL RES I/II, SUN RES, DIR BUR, NFPA 70/NEC, NFPA 79 compliance, WTTC 1000V, aluminium-coated foil, tinned-copper braiding и наружная оболочка из specially formulated thermoplastic polymer. Для Feichun такая конструкция является сильным ориентиром экранированного tray cable; для портовых кранов, судоразгрузчиков, горнодобывающей техники и тяжёлых подвижных машин её необходимо дополнить анализом растяжения, истирания, динамического изгиба, torsion movement и фактической среды эксплуатации.